KROHNE OPTISOUND 3020 C Handbook Download Page 6

Page: 6 / 52

2 For your safety

OPTISOUND 3020 C • Two-wire 4 … 20 mA/HART

30507-EN-190318

reasons, only the accessory specified by the manufacturer must be

used.
To avoid any danger, the safety approval markings and safety tips on

the device must also be observed and their meaning read in this oper-

ating instructions manual.

2.5 Safety label on the instrument

The safety approval markings and safety tips on the device must be

observed.

2.6 EU conformity

The device fulfils the legal requirements of the applicable EU direc-

tives. By affixing the CE marking, we confirm the conformity of the

instrument with these directives.

2.7 Fulfillment of NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

accepted as the standard in field instrumentation.
The device fulfils the requirements of the following NAMUR recom-

mendations:

•

NE 21: 2012 – Electromagnetic compatibility of equipment

•

NE 43 – Signal level for fault information from measuring transduc-

ers

•

NE 53 – Compatibility of field devices and display/adjustment

components

For further information see www.namur.de.

2.8 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.
Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).
Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code.

Summary of Contents for OPTISOUND 3020 C





















































Search results

Summary of Contents for OPTISOUND 3020 C

Reviews:

Related manuals for OPTISOUND 3020 C

Brands by name

Popular brands

KROHNE OPTISOUND 3020 C, Handbook

Search results

Summary of Contents for OPTISOUND 3020 C

Reviews:

Related manuals for OPTISOUND 3020 C

Brands by name

Popular brands