KROHNE OPTISOUND 3020 C Handbook Download Page 38

Page: 38 / 52

6 Set up with the display and adjustment module

OPTISOUND 3020 C • Two-wire 4 … 20 mA/HART

30507-EN-190318

•

Date of last change using PC: Date of the last change of sensor

parameters via PC

Last change using PC

•

Sensor details, e.g. approval, process fitting, seal, measuring cell,

measuring range, electronics, housing, cable entry, plug, cable

length etc.

Sensor characteristics

Display now?

6.4 Menu schematic

Basic adjustment

▶

Basic adjustment

Display
Diagnostics
Service
Info

Min. adjustment

1.1

0.00 %

4.000 m(d)

3.000 m(d)

Max. adjustment

1.2

100.00 %

1.000 m(d)

2.000 m(d)

Medium

1.3

Liquid

Vessel form

1.4

Storage tank

Damping

1.5

0 s

Linearisation curve

1.6

Linear

Sensor-TAG

1.7

Sensor

Display

Basic adjustment

▶

Display
Diagnostics
Service
Info

Displayed value

2.1

Scaled

Display unit

2.2

Volume
m³

Scaling

2.3

0 % = 0.0 m³

100 % = 100.0 m³

Summary of Contents for OPTISOUND 3020 C





















































Search results

Summary of Contents for OPTISOUND 3020 C

Reviews:

Related manuals for OPTISOUND 3020 C

Brands by name

Popular brands

KROHNE OPTISOUND 3020 C, Handbook

Search results

Summary of Contents for OPTISOUND 3020 C

Reviews:

Related manuals for OPTISOUND 3020 C

Brands by name

Popular brands