manualshive.com logo in svg

Krill Avanti S jet 2.1m ARF, Assembly Manual

Share
Download
Krill Avanti S jet 2.1m ARF Assembly Manual Download Page 1

 

 

 

 

 

The all new sport/3d jet is a masterpiece!! Designed by Italy’s Sebastiano Silvestri. Its 
design is based on a hawk aircraft. And then been improved further with aerodynamic 

ideas learned on other pattern models.it is a very lightweight and strong construction. 

This helps, as the flight speed rang is really impressive!! Designed to take an engine with 

100n of thrust, it is setup to be an ideal jet trainer BUT with a 220-250n turbine you have 

the ultimate 3d jet!!  

This will let you into a totally different flying experience!!  

Krill Avanti S jet 2.1m ARF

 

Assembly manual. 

Specification:                                  setup range of installation: 

Wingspan:…2.1m                           Turbine:…..from 100n to 250n 

Length:….2.22m                             radio:…..9-12 channel radio system 

Weight: RTF dry (p100)…10.5kg    servos:8 digital, metal gear servos. 

 

1. 

     

  

Summary of Contents for Avanti S jet 2.1m ARF




























Reviews:

No comments

Brands by name

Popular brands

Load more brands