Krell Industries KPE Instructions For Use Manual Download Page 7

Page: 7 / 18

Unpacking

Krell KPE

Open the box and remove the top layer of protective foam. The fol-
lowing items are visible:

1 Reference KPE phono amplifier

1 DC power connecting cable

1 T15 Torx wrench

1 warranty card

If ordered with the optional power supply the following items will also
be included:

1 Reference KPE power supply

1 AC power cord

Remove the plastic covering from the Reference KPE, DC power
cable and, if included, from the power supply.

Notes

REFERENCE KPE

Open the box and remove the top layer of protective foam. The fol-
lowing items are visible:

1 KPE phono amplifier

1 DC power connecting cable

1 T15 Torx wrench

1 warranty card

If ordered with the optional power supply the following items will also
be included:

1 KPE power supply

1 AC power cord

Remove the plastic covering from the Standard KPE, DC power
cable and, if included, from the power supply.

If any of these items are not included in the box, please contact your autho-
rized dealer or distributor immediately for assistance.

Save all packing materials. If you ship your KPE in the future, repack the
unit in its original packaging to prevent shipping damage.

STANDARD KPE

Summary of Contents for KPE



















Search results

Summary of Contents for KPE

Reviews:

Related manuals for KPE

Brands by name

Popular brands

Krell Industries KPE, Instructions For Use Manual

Search results

Summary of Contents for KPE

Reviews:

Related manuals for KPE

Brands by name

Popular brands