Krell Industries KPE Instructions For Use Manual Download Page 18

Page: 18 / 18

Reference KPE

FREQUENCY RESPONSE

20 Hz–20 kHz +/-0.1 dB

SIGNAL TO NOISE RATIO

“A” WEIGHTED

w/ 0.5 mv input

-80 dB

GAIN

58-76 dB in 6 dB increments

INPUT IMPEDANCE

Adjustable from 10 Ohms
to 1 K Ohms

POWER SUPPLY

Optional

DIMENSIONS

KPE

7.1w x 2.4h x 12d in.
18w x 6.1h x 30.5d cm

POWER SUPPLY

8.3w x 2.5h x 6.5d in.
21.1w x 6.4h x 16.5d cm

WEIGHT

WITHOUT POWER SUPPLY

Shipped

12 lb., 5.5 kg

Standard KPE

FREQUENCY RESPONSE

20 Hz–20 kHz +/-0.1 dB

SIGNAL TO NOISE RATIO

“A” WEIGHTED

w/ 0.5 mv input

MC: -71 dB
MM: -89 dB

GAIN

MC: 64.5 dB
MM: 36.5 dB

INPUT IMPEDANCE

Adjustable from 10 Ohms
to 47 K Ohms

POWER SUPPLY

Optional

DIMENSIONS

KPE

7.1w x 2.4h x 12d in.
18w x 6.1h x 30.5d cm

POWER SUPPLY

8.3w x 2.5h x 6.5d in.
21.1w x 6.4h x 16.5d cm

WEIGHT

WITHOUT POWER SUPPLY

Shipped

12 lb., 5.5 kg

Krell Industries, Inc.
45 Connair Road
Orange, CT 06477-3650 USA

TEL 203-799-9954, FAX 203-891-2028
E-MAIL [email protected]
WEB SITE www.krellonline.com

Reference KPE

Standard KPE

Phono Preamplifier

v 02.1

Specifications

All operational features, functions,
specifications, and policies are
subject to change without
notification.

Summary of Contents for KPE



















Search results

Summary of Contents for KPE

Reviews:

Related manuals for KPE

Brands by name

Popular brands

Krell Industries KPE, Instructions For Use Manual

Search results

Summary of Contents for KPE

Reviews:

Related manuals for KPE

Brands by name

Popular brands