background image

 

WP-110xl - Getting Started

 

 

2.2 

Safety Instructions 

 

Caution: 

There are no operator serviceable parts inside the unit 

Warning: 

Use only the Kramer Electronics input power wall 
adapter that is provided with the unit 

Warning: 

Disconnect the power and unplug the unit from the wall 

before installing  

2.3 

Shielded Twisted Pair/Unshielded Twisted Pair   

We recommend that you use Shielded Twisted Pair (STP) cable, and stress that 

the compliance to electromagnetic interference was tested using STP cable. There 

are different levels of STP cable available, and we advise you to use the best 

quality STP cable that you can afford.

 

Our non-skew-free cable, Kramer

 BC-STP

 

is intended for analog signals where skewing is not an issue. 

In cases where there is skewing, our Unshielded Twisted Pair (UTP) skew-free 

cable, Kramer 

BC-XTP

, may be advantageous, and UTP cable might also be 

preferable for long range applications. In any event when using UTP cable, it is 

advisable to ensure that the cable is installed far away from electric cables, motors 

and so on, which are prone to create electrical interference. 

2.4 

Recycling Kramer Products 

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC 

aims to reduce the amount of WEEE sent for disposal to landfill or incineration by 

requiring it to be collected and recycled. To comply with the WEEE Directive, 

Kramer Electronics has made arrangements with the European Advanced 

Recycling Network (EARN) and will cover any costs of treatment, recycling and 

recovery of waste Kramer Electronics branded equipment on arrival at the EARN 

facility. For details of Kramer’s recycling arrangements in your particular country 

go to our recycling pages at 

http://www.kramerelectronics.com/support/recycling/

 

!

Summary of Contents for WP-110xl


















Reviews: