background image

KRAMER:  SIMPLE CREATIVE TECHNOLOGY

 

Getting Started 

 

2.1 

Achieving the Best Performance 

To achieve the best performance: 

 

Use only good quality connection cables (we recommend Kramer high-

performance, high-resolution cables) to avoid interference, deterioration in 
signal quality due to poor matching, and elevated noise levels (often 
associated with low quality cables) 

 

Do not secure the cables in tight bundles or roll the slack into tight coils 

 

Avoid interference from neighboring electrical appliances that may adversely 

influence signal quality  

 

Position your Kramer 

RC-53DLC 

away from moisture, excessive sunlight and 

dust 

 

 

 

This equipment is to be used only inside a building. It may only be 

connected to other equipment that is installed inside a building.

 

2.2 

Safety Instructions 

 

 

 

 

Caution: 

There are no operator serviceable parts inside the unit

 

Warning: 

Use only the Kramer Electronics input power wall 

adapter that is provided with the unit 

Warning: 

Disconnect the power and unplug the unit from the wall 

before installing  

2.3 

Recycling Kramer Products 

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC 
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by 
requiring it to be collected and recycled. To comply with the WEEE Directive, 
Kramer Electronics has made arrangements with the European Advanced 
Recycling Network (EARN) and will cover any costs of treatment, recycling and 
recovery of waste Kramer Electronics branded equipment on arrival at the EARN 
facility. For details of Kramer’s recycling arrangements in your particular country 
go to our recycling pages at 

http://www.kramerelectronics.com/support/recycling/

 
 
 
 
 
 

!

!

Summary of Contents for K-NET RC-53DLC



















Reviews: