manualshive.com logo in svg

Kramer FC-404NETxl, User Manual, Page: 10 / 53

Share
Download
Kramer FC-404NETxl User Manual Download Page 10

Kramer Electronics Ltd. 

 

FC-404NETxl 

– Connecting FC-404NETxl 

8 

 

Connecting the Outputs 

Your 

FC-404NETxl

 is provided with a 3-pin terminal block for each output channel. This 

connector offers a balanced output to interface with the input of another device. 

Connection methods for balanced and unbalanced outputs are identical as the methods for 
inputs as referenced in 

Connecting the Inputs

 on page 

6

. 

Connecting to FC-404NETxl via RS-232 

You can connect to 

FC-404NETxl

 via an RS-232 connection 

 using, for example, a PC. 

FC-404NETxl

 features an RS-232 3-pin terminal block connector allowing the RS-232 to 

control 

FC-404NETxl

. 

Connect the RS-232 terminal block on the rear panel of 

FC-404NETxl

 to

 

a PC/controller, as 

follows: 

From the RS-232 9-pin D-sub serial port connect: 

•

 

Pin 2 to the TX pin on the 

FC-404NETxl

 RS-232 terminal 

block 

•

 

Pin 3 to the RX pin on the 

FC-404NETxl

 RS-232 terminal 

block 

•

 

Pin 5 to the G pin on the 

FC-404NETxl

 RS-232 terminal block

 

RS-232 Device       FC-404NETxl

 

 

13 

Summary of Contents for FC-404NETxl






















































Reviews:

No comments