32
33
СТИРАЛЬНАЯ МАШИНА АВТОМАТ
AUTOMATIC WASHING MACHINE
СТИРАЛЬНАЯ МАШИНА АВТОМАТ
AUTOMATIC WASHING MACHINE
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ • USEr GUIdE
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ • USEr GUIdE
6
10
0c
m
65
cm
Install Washing Machine
Connect the inlet hose
1.Connect the inlet hose to tap and
fasten it anticlockwise.
2.Connect the other end of the inlet hose to the inlet valve at the backside
of the washing machine and fasten the hose tightly clockwise.
when there is a inlet at the back of the machine,it must be connected to
a cold water supply.If there are two inlet valve,one is connected to a
cold water supply and the other is connected to a hot water supply.
Follow the indication of the picture below to complete the connection.
inlet valve for cold water
inlet hose for cold water
inlet hose for hot water with a red side
inlet valve for hot water with a red grid
If there is any leakage with hose after
the connection,then repeat the steps to
connect inlet hose.
Do not bend the hose.
Check for inlet hose connection carefully
before using the washer each time.
Connect the drain hose
The drain hose shall be placed at a
height of 65-100cm above the floor,
otherwise,it can cause poor drainage
You can use the supplied drain hose
support bracket to loop the drain hose
down into the wall,standpipe or laundry
tub.
Take care to ensure all hose connections
are tight.
The end of the drain hose cannot be
immersed in water for the washer to work
properly.
NOTE
NOTE
Install Washing Machine
Remove transit bolts
Before using this washing
machine, transit bolts
must be removed from the
backside of this machine.
Please take the following
steps to remove the bolts
:
1. Loosen the four transit bolts with a spanner
2. Take each bolt head and pull it through the wide part of the hole. Repeat for each bolt.
3. Fill the holes with the supplied plastic covers.
4. Keep the transit bolts properly for futher use.
Levelness adjustment
Do not place the washing machine outdoors or in a place below 0 °С, otherwise the program
controller tends to be damaged.
•
Check whether the feet are in their states as delivered (the rubber pad fits bottom of the inner tub
box closely; the lock nut is securely locked on the rubber pad) or not and, if not, restore them to
their states as delivered.
• Press opposite angles of the top cover plate, press the top cover plate vertically to shake the
washing machine to check whether its feet are in close contact with the floor or not.
• Rotate the feet leftward or rightward to adjust the levelness till they are in close contact with the
floor and the washing machine does not shake.
WARNING
• When the four feet are in close contact with the floor, the washing machine must be completely
level and secure. When the washing machine is level, make the feet as low as possible.
• Improper levelness adjustment will result in the washing machine’s big noise, vibration,
displacement, etc.
• There is a vent at bottom of the washing machine (do not block it). Place the washing machine
on a solid, flat and skidproof floor. To avoid injuries, do not place the washing machine on soft
blanket, wooden floor, platform or rack.
6
10
0c
m
65
cm
Install Washing Machine
Connect the inlet hose
1.Connect the inlet hose to tap and
fasten it anticlockwise.
2.Connect the other end of the inlet hose to the inlet valve at the backside
of the washing machine and fasten the hose tightly clockwise.
when there is a inlet at the back of the machine,it must be connected to
a cold water supply.If there are two inlet valve,one is connected to a
cold water supply and the other is connected to a hot water supply.
Follow the indication of the picture below to complete the connection.
inlet valve for cold water
inlet hose for cold water
inlet hose for hot water with a red side
inlet valve for hot water with a red grid
If there is any leakage with hose after
the connection,then repeat the steps to
connect inlet hose.
Do not bend the hose.
Check for inlet hose connection carefully
before using the washer each time.
Connect the drain hose
The drain hose shall be placed at a
height of 65-100cm above the floor,
otherwise,it can cause poor drainage
You can use the supplied drain hose
support bracket to loop the drain hose
down into the wall,standpipe or laundry
tub.
Take care to ensure all hose connections
are tight.
The end of the drain hose cannot be
immersed in water for the washer to work
properly.
NOTE
NOTE
• The drain hose shall be placed at a height of
85-125 cm above the floor, otherwise,it can cause
poor drainage.
• You can use the supplied drain hose support
bracket to loop the drain hose down into the
wall,standpipe or laundry tub.
• Take care to ensure all hose connections are
tight.
