background image

36

  REPLACEMENT PARTS LIST

15.0  REPLACEMENT PARTS LIST

Replacement parts are available through your local dealer. Contact your local dealer for availability and pricing. 

CONTROL BOARD AND PARTS

Control Board - NG

J30-160 Valve Step Motor - LPG

700-504-1

Control Board - LPG

J30-161 18 in. Flexible Gas Line - Black

700-213B

S.I.T. IPI Gas Valve - NG

700-567 Flexible Gas Line - Valve to Burner Connection

700-226

S.I.T. IPI Gas Valve - LPG

700-567-1 NG Burner Orifice #53 FRONT

700-253

Proflame 2 IFC Board

700-652 NG Burner Orifice #44 BACK

700-244

IFC Wire Harness Assembly

700-653 LPG Burner Orifice #61 FRONT

700-261

Pilot Assembly - NG

700-551 LPG Burner Orifice #55 BACK

700-255

Pilot Assembly - LPG

700-551-1 Conversion Kit - NG

NCK-J30-S

540 Split Flow 

700-595 Conversion Kit - LPG

LCK-J30-S

Transmitter (Remote Control) with Split flow

700-508 Front Burner

J30-350

Pilot Orifice - NG #62

700-166 Back Burner

J30-351

Pilot Orifice - LPG #35

700-168 Battery Holder

700-419

Valve Step Motor - NG

700-504

LOG SET

8 Piece Log Set

J30-500

Ember Panel

J30-900E

#1 Log

J30-1

#2 Log

J30-2

#3 Log

J30-3

#4 Log

J30-4

#5 Log

J30-5

#6 Log

J30-6

#7 Log

J30-7

#8 Log

J30-8

Rock Wool Embers

900-REMB

GLASS AND GLASS PARTS

Glass with Gasket 255/8” x 17½”

JOR-057T

Valance

JOR-005

Glass Gasket

900-006

Hussong Manufacturing Co., Inc.  
P.O. Box 577 
204 Industrial Park Drive 
Lakefield, MN 56150-0577
JOR-30S

SAFETY BARRIERS

Beveled Screen Front

J30-BSF

Convex Screen Front

J30-CXF

Prairie Screen Front

J30-PSF

Rectangular Screen Front

J30-RSF

Arched Mission Screen Front

J30A-MSF

Arched Prairie Screen Front

J30A-PSF

Arched Screen Front

J30A-SF

Arched Full Prairie Door Screen Front

J30A-FPDSF

Summary of Contents for JOR-30S








































Reviews: