background image

Page 1

C H I N O O K   F I R E P L A C E S

Models SBI-30A/BWI-30A

GAS FIREPLACE INSERT
Homeowner and Installation Manual

This Manual contains important details concerning:

• Installation                                    • Operation                                   • Maintenance

                           • Replacement Parts                  • Trouble Shooting

THIS APPLIANCE IS CERTIFIED TO CSA 2.22 AND

ANSI Z21.50 VENTED GAS FIREPLACE

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING THIS APPLIANCE

PLEASE ENSURE THAT THIS MANUAL REMAINS WITH THE APPLIANCE

- Do not store or use gasoline or other
  flammable vapours and liquids in the
  vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Open windows/extinquish all flames.
• Do not touch any electrical switch; do
  not use any phone in your building.
• Immediately call your gas supplier
  from a neighbour’s phone.
• Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier,
  call the fire department.

- Installation and service must be
  performed by a qualified installer,
  service agency or the gas supplier.

This product may be installed in factory built

fireplaces which meet the minimum size of

16” deep by 28” wide by 22” high.

CAUTION 

-

 

Do not make any modifications to

factory built fireplace or block cooling air circu-
lation ducts: Fire, Injury or Death could result.

WARNING:   If the information in these instructions are not followed exactly, a fire or
                              explosion may result causing property damage, personal injury or loss of life.

Rev 10/03

1060201

Summary of Contents for BWI-30A

















Reviews: