background image

8

 SPECIFICATIONS

2.0  SPECIFICATIONS

2.1  Appliance Components

Part Number

Description

B41L-150A

Control Board Assembly

700-203 

Manual Gas Shut-of Valve 

B41L-135A

Burner Assembly

B41L-500

Log Package 

900-085

4 in Restrictor Plate

B41-057T

Glass Frame Assembly

IPI-028

Fan Kit (2)-75 CFM

700-408

Remote Control

2.1.1  Additional Components Required

Refer to Section 7.0 Venting on page 22, for approved vent 
systems. 

2.2  Heating Specifications

Natural Gas

LP Gas

Maximum  
Input Rating

30,000 Btu/h

(8.8 KW)

30,000 Btu/h

(8.8 KW)

Minimum  
Input Rating

15,500 Btu/h 

(4.5 kW)

15,500 Btu/h 

(4.5 kW)

Manifold Pressure 
(High)

3.8” WC

(0.95 kPa)

11” WC

(2.74 kPa)

Manifold Pressure 
(Low)

1.1” WC

(0.27 kPa)

2.9” WC

(.72 kPa)

Orifice Size (DMS) 

#41

#.0625

2.2.1  Altitude Adjustment

This appliance may be installed at higher altitudes. Please refer 
to National Fuel Gas Code ANSI Z223.1/NFPA 54, CSA-B149.1 
Natural Gas and Propane Installation Code, local authorities, 
or codes having jurisdiction in you area regarding derate 
guidelines. 

2.2.1.1  US Installations

Refer to the American Gas Association guidelines for the gas 
designed appliances derating method. For elevations above 2,000 
ft (610 m), input ratings are to be reduced by 4% for each 1,000 ft 
(305 m) above sea level. 

2.2.1.2  Canadian Installations

When the appliance is installed at elevations above 4,500 ft (1,372 
m), the certiied high altitude rating shall be reduced at the rate of 
4% for each additional 1,000 ft (305 m).

Summary of Contents for BAYPORT-41 GLASS


















































Reviews: