background image

LIMITED WARRANTY 

41

LIMITED WARRANTY

Kozy Heat Limited 10 Year Warranty

This limited 10 Year Warranty will not become effective until the 
Warranty Registration Form has been completed and mailed to 
Hussong Manufacturing Co., Inc., P.O. Box 577, Lakefield, MN 
56150. This registration form must be received within 30 days 
of installation. Failure to do so may result in delayed warranty 
coverage and submission of proof of purchase will be required.

Hussong Manufacturing Co., Inc. warranties to the original 
purchaser of this Kozy Heat Fireplace, that it is free of defects in 
materials and workmanship at the time of manufacture.

Subject to the following conditions & requirements, Hussong 
Manufacturing Co., Inc. extends the following limited warranty 
under normal use and service, with respect to the Kozy Heat line of 
gas burning fireplaces.

Year 1

Subject to the conditions & requirements listed below, within the 
first year from date of purchase, Hussong Manufacturing Co., Inc. 
shall, at its discretion, replace or repair any such defect in  material 
or workmanship, at Hussong Manufacturing Co., Inc.’s expense, 
including reasonable labor costs to repair or replace the defective 
component, if a factory pre-authorization is given for the repair. 

Years 2 through 10

Subject to the conditions & requirements listed below, beginning 
with the first day of the second year and continuing through the 
tenth year, Hussong Manufacturing Co., Inc., will at its discretion, 
provide repair or replacement parts at current list prices for any 
defect in material or workmanship of components, including 
optional components and accessories (if available). Hussong 
Manufacturing Co., Inc. shall not be  responsible for any installation, 
labor, transportation of other indirect costs.

Limitation of Liability

To make a claim under this warranty, the purchaser must first 
contact the dealer/installer from whom the fireplace was purchased.

This limited warranty will be void if the fireplace is not installed by a 
qualified installer and according to the installation instructions. Use 
of unauthorized components will make this warranty null and void.

This limited warranty also is void if the fireplace is not operated, at 
all times, according to the operating instructions furnished.

This warranty is limited to defects in material and workmanship. It 
does not apply to any product that has been subject to negligence, 
misapplication, improper installation. 

No person is authorized to extend the time of this warranty or to 
accept on Hussong Manufacturing Co., Inc.’s behalf any additional 
obligation of liability connected with the unit. 

It is expressly agreed and understood that this warranty is Hussong 
Manufacturing Co., Inc.’s sole obligation and purchaser’s exclusive 
remedy for defective fireplace equipment. Hussong Manufacturing 
Co., Inc. shall not be liable for any consequential, incidental or 
contingent damages whatsoever. The foregoing warranty is 
exclusive and in lieu of all other expressed warranties. Hussong 
Manufacturing Co., Inc. shall not be held to implied warranties or 
merchantability and fitness for a particular purpose. This warranty 
replaces all previous warranty policies.

Some states do not allow the exclusion or limitation of incidental 
or consequential damages or limitations on how long an implied 
warranty lasts, so the above limitations or exclusions may not apply 
to you. This warranty gives you specific legal rights and you may 
also have other rights which vary from state to state.

Hussong Manufacturing Co., Inc. reserves the right to make changes 
at any time, without notice, in design, material, specifications and 
prices. Hussong Manufacturing Co., Inc. reserves the right to 
discontinue models and products.

September 2011

Warranty Conditions and Requirements

1.  You are the original purchaser. This warranty is not transferable.

2.  Installation of the fireplace is performed by a qualified installer.

3.  Installation and operation must comply with installation and operation instructions.

4.  Paint and glass gaskets are covered for 30 days from date of purchase.

5.  Remote controls and all optional accessories are covered for 1 year from date of purchase.

6.  This warranty does not offer coverage for Light Bulbs or Batteries (whether factory, dealer or installer supplied). This includes 

any damage stemming from either component’s nonuse.

7.  Components broken, (including glass panels), during shipping, careless handling of components, or defects resulting from 

improper installation, misuse of the fireplace and components are not covered under this warranty.

8.  This warranty does not cover any part of the fireplace or any components which have been exposed to or submerged 

underwater. 

9.  Hussong Manufacturing Co., Inc. must be notified by the dealer the fireplace was purchased from or a qualified installer/service 

technician of the defect. 

10.  Annual service of the fireplace as required in the installation manual, is performed by a qualified installer/service technician.   

(Copies of such service records may be required to claim a warranty). 

11.  All previous warranty/service has been performed by a qualified installer or service technician.  

(Copies of such service records may be required to claim a warranty).

Summary of Contents for BAY-36-MV












































Reviews: