background image

 

 

 

 
 

 

Page 5

 

 

Always wear a dust mask when cleaning the system and when removing ashes to avoid damages 

to your health. 

 

When setting the domestic water temperature above 60 °C, you have to ensure that the hot water 

is mixed with cold water to avoid scald. 

 

The pellet heater system may only be set up and operated in heating and plant rooms which 

comply with legal requirements. 

 

Provide an appropriate air relief valve on top of the boiler. 

 

Annual control of safety devices by a specialist. 

 

Regular control of expansion tank by a specialist. 

 

Regular control of pellet feeding devices, automatic ignition devices and feeding features. 

 

Please note that even when the system is turned off, different functions are in operation. 

(For example the anti-freeze protective device; pumps and mixers are moved periodically during 

the night avoid an accumulation of the storings). 

To ensure that no electricity runs through 

the system, take off the system from electricity.

  

 

Make sure that the return temperature does not drop below 50 °C. Disregarding leads to expiry 

of warranty! 

 

 

 

 

 

 

 

 

Summary of Contents for SLIMPEL






















Reviews: