DISK
1.1
131
25) Load .WAV:
selected icon
The selected WAVE file will be loaded as a sample.
1
To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The sample will be loaded following the last-numbered
sample that currently exists in memory by having been
sampled or loaded (Append load).
Files with an extension of other than .AIF/.WAV cannot
be recognized as AIFF/WAVE files. In this case, use the
Utility “Rename” (1.1–3a) to change the last four char-
acters of the filename to “.AIF”/“.WAV”
If the data that is loaded as a sample contains a loop
point, you can set “S.Ofs(Start Offset)” (PROG 2.1–2b/
3b) on the TRITON-Rack so that the sound will begin
from the loop point.
If data whose sample size is 8 bits or less is loaded, it
will be converted into 16 bit data inside the TRITON-
Rack. This will mean that the amount of internal mem-
ory consumed will be approximately twice as large as
the file size. The increase in size resulting from this con-
version may mean that it is impossible to save that data
on a floppy disk.
Loading AKAI S1000/S3000 format Sample files and
Program files
The TRITON-Rack can load AKAI S1000/S3000 format Sam-
ple files and Program files. The loaded Sample or Program
file data can be used as a sample or multisample respec-
tively. When the loaded data is then saved to storage media,
it will be saved as a Korg format .KSF file or .KMP file
respectively.
AKAI S1000/S3000 format stereo Sample files and Program
files whose names end in “-L” and “-R” can be loaded into
the TRITON-Rack as stereo samples and multisamples.
When the above files are loaded, “-L” and “-R” will auto-
matically be moved to the end of the sample name or multi-
sample name (15th and 16th character) so that they can
automatically be recognized as stereo samples or multisam-
ples.
26) Load AKAI Sample File:
selected icon
The selected Sample will be loaded as a sample.
1
To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The sample will be loaded following the last multisample
or sample that currently exists in the TRITON-Rack’s
memory by having been sampled or loaded (Append
load). If the loaded data is then saved to storage media, it
will be saved as a Korg format .KSF file. (possible to
export as a .AIF, .WAV format
p.135 “Export Smpl AIF/
WAV”)
If the data that is loaded as a sample contains a loop
point, you can set “S.Ofs(Start Offset)” (PROG 2.1–2/
3b) on the TRITON-Rack so that the sound will begin
from the loop point.
If the end (11th and 12th characters) of the sample name
is “-L” and “-R,” the “-L” and “-R” will automatically
be moved to the end of the TRITON-Rack’s sample
name (15th and 16th characters).
When you load two files whose sample names are iden-
tical except for ending in “-L” and “-R,” and assign
them to a stereo multisample in Sampling mode, they
will be recognized as a stereo sample.
Sample files
27) Load AKAI Program File:
selected icon
The selected Program file will be loaded as a multisample.
When the loaded data is saved to storage media, a Program
file will be saved as a .KMP file, and a Sample file will be
saved as a .KSF file.
1
To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
Samples will be loaded starting at the first unoccupied
number following the last multisample or sample that
currently exists in TROTON-Rack’s memory by having
been sampled or loaded. Only valid Program files or
Samples files will be loaded (Append load).
If the Sample files used by the Program file are not in the
current directory or below it, a dialog box will appear,
allowing you to specify the directory. Use the procedure
“If the file to load cannot be found,…” (
the required Sample files.
Since PCM memory overflow checking is performed
when loading each sample file, an overflow may occur
during the loading process.
If a loaded multisample is assigned samples whose
sample names end in “-L” and “-R,” an “-L” and “-R”
will automatically be added to the end (15th and 16th
characters) of the multisample name.
When you load two multisamples whose multisample
names are identical except for ending in “-L” and “-R,”
they will be recognized in Sampling mode as a stereo
multisample.
Parameter
AKAI S1000/S3000
format
TRITON-Rack format
after loading
Loop points Multiple settings possible
Of the multiple loop points,
the settings for the first
HOLD loop are used.
If there is no HOLD loop,
use the longest loop
Loop length Settable with resolution
of less than one sample
Resolution of less than one
sample is ignored
