background image

4

IV. Product Identification and Nameplate 

 

Each Kooltronic Air Conditioner includes an identification nameplate. This nameplate provides: 

 

q

Model Number 

w

Serial Number

 

e

Electrical power characteristics 

r

Maximum and minimum ambient operating temperatures 

t

Cooling capacity 

y

Type and amount of refrigerant required for recharging 

u

Design Pressure 

i

Maximum Fuse Size 

o

Manufacturing Order Number 

a

Filter Part Number 

s

Underwriters Laboratories Inc. Listed or Recognized Marks and NEMA ratings 

 

 

We recommend you copy this information from your unit. 

qwo

 

When ordering parts, specify the Model Number, Serial Number & MFG. Order Number.

e

 

Before operating, be sure that the power source matches these requirements.

y

 

Use of incorrect type or amount of refrigerant will adversely affect performance and may damage the unit.

Make sure that these parameters are met. Failure to do so may result in permanent damage to the unit.

ALL MOTORS ARE THERMALLY PROTECTED

VIOLATES WARRANTY

UNAUTHORIZED SERVICE OR MODIFICATION

INDOOR USE

COMPARTMENT ONLY

NEMA/EEMAC/UL50 BY UNDERWRITERS LABORATORIES, INC.

TYPE 1 SPECIAL PURPOSE AIR CONDITIONER EQUIPMENT

SPECIAL PURPOSE AIR CONDITIONER

FUSE SIZE

MAX.

HIGH

LOW

Oz.

REFRIGERANT

MAX.°F

MIN.°F

AMBIENT TEMP.

COOLING

ALLOW 5 MIN. BEFORE RESTARTING AFTER SHUTDOWN

Air Conditioner

DESIGN PRESSURE P.S.I.G.

MFG. ORDER NO.

KOOLTRONIC, INC.   PENNINGTON, NJ

MANUFACTURED BY:

COOLING BTU

F.L.A.

PH.

FREQ.

VOLTS

SERIAL NUMBER

MODEL NUMBER

FILTER P/N

q

w

e

e

e

e

r

r

t

y

u

u

i
o
a

s

LISTED 84H7

SPECIAL PURPOSE

AIR CONDITIONER

Summary of Contents for Intrepid Series


















Reviews: