background image

TABLE OF CONTENTS

 

 

                                                                                                                         

Page

 

                   

I.                         Introduction                                                                              2 

                     II.                         Incoming Inspection                                                                 3 

                    III.                         Product Handling                                                                     3 

                    IV.                         Product Identification and Nameplate                                      4 

                     V.                         Principles of Operation                                                       5 - 8   

                    VI.                         Pre-Installation Testing                                                             8 

                   VII.                         Specific Model Data                                                         9 - 13 

                                                       Mounting 

                                                       Drawings and Dimensions 

                                                       Technical Data 

                                                       Major Component Replacements 

                                                       Standard Features 

                                                       Wiring Diagram 

                                                       Commissioning/Test Results 

                  VIII.                         Maintenance                                                                   14 - 15 

                    IX.                         Trouble Shooting                                                                    16 

                     X.                         Warranty                                                                                17 

 
 
 
 

I. Introduction

 

 

Kooltronic Air Conditioners are designed to provide a cool, dehumidified environment for your electronic 
components. There are models to fit virtually all sizes and shapes of  electronics enclosures, in 
capacities ranging from 1,000 to 30,000 BTU/H. Our "closed-loop" design also ensures that your 
components will not be exposed to hot, dirty operating conditions. 
 
This Manual provides you with the necessary general information for properly installing and operating 
standard Kooltronic Air Conditioners. Technical data and mounting instructions are presented on pages 
9 through 13. 

2

Summary of Contents for Intrepid Series


















Reviews: