manualshive.com logo in svg

Kontron R4U8S, Installation And User Manual

Share
Download
Kontron R4U8S Installation And User Manual Download Page 28

R4U8S User's Manual

Hardware Description

SD.DT.F06-1e

 Page 

21

4.6.2

Installing two 3.5" HDD on Top of the Power Supply Unit

Up to two 3.5 inch hardware disks may be installed on a specific support  located on top of the power supply unit.
This specific support is accessible by removing the cover of the rack.

Assembling Procedure

1. Power-off the rack (ON/OFF buttton).

2. Remove the cover of the rack. Unscrew the screws by using a Pozidriv screwdriver.

If the disks are installed on the specific support, make sure to remove the connectors between
the disks and the boards and between the disks and the power supply before removing the
cover of the rack.

3. While holding the specific support, unscrew the disk mounting screws from the cover of the rack.

4. Install/Uninstall the disks on the specific support. Each disk is fixed to the specific support with four screws.

5. While holding the specific support, screw the disk mounting screws removed at stage 3. to fix the specific

support  to the cover of the rack.

6. Plug the connectors between the disks and the boards, and between the disks and the power supply.

7. Install the cover of the rack. Fix it to the rack frame with the screws removed at stage 2.

8. Power-on the rack.

4.6.3

Installing two 2.5" HDD on a Specific Tray

Up to two 2.5 inch hardware disks may be installed on an optional tray. This optional tray may be inserted in a
free slot of the rack, RTM  bay side or the 6U VME boards side; depending on the configuration of the rack. This
tray takes up one slot.

Assembling Procedure

Contact your Kontron representative for more information on this topic.

4.6.4

Installing two 3.5" HDD on a Specific Tray

Up to two 3.5 inch hardware disks may be installed on two optional trays. Each optional tray may be inserted
in a free slot of the rack, 6U VME boards side only. One disk only may be installed by tray, each tray takes up
two slots.

Installing two 3.5 inch HDD, will leave only four free slots in the rack.

Assembling Procedure

Contact your Kontron representative for more information on this topic.

Summary of Contents for R4U8S































Reviews:

No comments

Brands by name

Popular brands

Load more brands