background image

R4U8S User's Manual

Hardware Description

Page 14 

 

SD.DT.F06-1e

4.3

Control Panel

4.3.1

Front Control Panel

ON/OFF Button

Control Lights

Pass-through RJ-45

Figure 8: Front Control Panel

Depending on the 

6U VME Boards Bay

 Manufacturing option, the front control panel may be located on

the left side or on the right side of the front panel:

6U VME Boards Bay: 

 

Front

the front control panel is located on the 

right 

side of the front panel

(refer to Figure 8).

6U VME Boards Bay: 

Rear

the front control panel is located on the 

left 

side of the front panel.

4.3.1.1

ON/OFF Button

The ON/OFF button is located on the front panel of the R4U8S rack.

DO NOT turn the power on while the power is cycling off. Wait a few seconds until the power has
completely cycled off. Follow the same precaution for turning the power off. 
Turning the power on or off before this cycle is complete can cause the voltage and temperature values
programmed into the board monitoring system to be lost.
MAKE SURE YOU FOLLOW THESE SAFETY PRECAUTIONS.

Make sure the rack has been powered off using the ON/OFF button (on the front control panel of the rack)
before unplugging the power supply cable.

4.3.1.2

Pass-through RJ-45

A pass-through RJ-45 plug allows the customer to easily route an Ethernet link to the front control panel.

Summary of Contents for R4U8S































Reviews: