- 94 -
!
SAFETY ADVICE
We strongly recommend the use of work gloves during assembly.
Do not attempt to assemble the Sliding roof canopy in windy or wet conditions,
Do not touch overhead power cables with the aluminum profiles.
Always wear shoes and safety goggles when working with extruded aluminum.
Dispose of all plastic bags safety-keep them out of reach of small children.
The Sliding roof canopy must be positioned and fixed on a flat level surface.
Do not lean against or push the Sliding roof canopy during construction.
Keep children away from the assemble area.
Do not position your Sliding roof canopy in an area exposed to excessive wind.
Do not attempt to assemble this Sliding roof canopy if you are tired ,have taken drugs or
alcohol or
if you are prone to dizzy spells.
If using a step ladder or power tools ensure that you follow the manufactures safety advice.
Hot items such as recently used grills, blowtorches etc.must not be stores in the Sliding roof
canopy .
Ensure there are no hidden pipes or cables in the ground before inserting the pegs.
GENERAL ADVICE
This is a multi-part assembly, Allow at least 180 minutes for assembly.
Selecting a site-choose a sunny level position away from overhanging trees.
If you are fixing your Sliding roof canopy directly to a solid concrete foundation use
the
pre drilled holes in the metal base supplied.
The component parts should be checked and laid out close at hand.
Keep all small parts(screws etc)in a bowl so they do not get lost.
Note that the door is hinged on the right hand side and therefore opens tothe right.
Keep roof clear of snow and leaves.
CARE & MAINTENANCE
When your Sliding roof canopy needs cleaning, use a mild detergent solution and
risen
with cols clean water.
Do NOT use acetone, abrasive cleaners or other special detergents to clean the
clear panels.
TOOLS & EQUIPMENT REQUIRED
Protective Equipment:
1.Helmet
2.Glove
3.Long Sleeve Cotton Overalls
4.Emergency Medicine Cabinet
5.Eye Shield
Measure (metric):
1.The Tape (5 m)
2.Angle Square
3.Level Meter
-2-
Installation Tool:
1.Triangle Stairs≈
2m Height
2.Spanner 10mm (Ratchet Wrench is better)
3.Spanner 14mm (Install the expansion screw)
4.Hexagon wrench 5mm
5.Electric scre4mm Hexagon wrench
(suggest)
6.Wooden Mallet
7.Marking Pen
8.Percussion bit(8mm and 10mm)
9.Knife
10.Phillips screwdriver
Ø3
CONSIGNES DE SÉCURITÉ
Il est fortement recommandé de porter des gants de travail pour le montage.
N‘essayez pas de monter la toiture flexible de terrasse lorsqu‘il y a du vent ou par
temps humide.
Veillez à ne toucher aucun caténaire électrique avec les profils en aluminium.
Lors du travail avec de l‘aluminium extrudé, il est conseillé de toujours porter des
chaussures et des lunettes de protection.
Mettez les emballages plastique au rebut de manière sûre et veillez à ce qu‘ils ne
tombent pas entre les mains de jeunes enfants.
La toiture doit être positionnée et ancrée sur une surface droite et plane.
Ne pas s‘adosser contre la toiture ni la décaler pendant le montage.
Les enfants doivent être tenus éloignés de la zone de travail.
Ne montez pas la toiture à un endroit exposé à un vent fort.
N‘essayez pas de monter la toiture lorsque vous êtes fatigué, si vous après pris de la
drogue ou de l‘alcool ou si vous êtes sujet à des vertiges.
Lors de l‘utilisation d‘échelles ou d‘outils électriques, les consignes de sécurité du
fabricant doivent être respectées.
Les objets brûlants, comme par ex. des grils, chalumeau etc. utilisés juste avant, ne
doivent pas être conservés sous la toiture de terrasse.
Assurez-vous qu‘aucune canalisation cachée ou câble ne se trouve dans le sol avant
d‘enfoncer les éléments de fixation dans le sol.
REMARQUES GÉNÉRALES
Le montage comporte différentes étapes. Prévoyez au minimum 180 minutes pour le
montage.
Choix de l‘emplacement : Choisissez un endroit ensoleillé et plan, loin d‘arbres en
surplomb.
Utilisez les trous pré-percés dans la partie métallique inférieure lorsque vou
souhaitez relier la toiture directement avec une fondation en béton massif.
Tous les composants doivent être contrôlés et être prêts à portée de main.
Conservez les petites pièces (vis, etc.) dans un récipient pour ne pas les perdre.
Dégagez la neige et les feuilles mortes sur le toit.
ENTRETIEN & MAINTENANCE
Si nécessaire, utilisez une solution de nettoyage douce pour nettoyer votre toiture de
terrasse et rincez les surfaces à l‘eau claire froide.
N‘utilisez PAS d‘acétone, de produit abrasif ou d‘autre produit de nettoyage agressif
pour nettoyer les plaques transparentes.
ÉQUIPEMENT &
OUTILS NÉCESSAIRES
Équipement de protection :
1. Casque de protection
2. Gants de travail
3. Combinaison en coton à manches longues
4. Trousse de premiers secours
5. Lunettes de protection
Instruments de mesure (métriques) :
1. Mètre ruban (5 m)
2. Inclinomètre
3. Niveau à bulle
!
SAFETY ADVICE
We strongly recommend the use of work gloves during assembly.
Do not attempt to assemble the Sliding roof canopy in windy or wet conditions,
Do not touch overhead power cables with the aluminum profiles.
Always wear shoes and safety goggles when working with extruded aluminum.
Dispose of all plastic bags safety-keep them out of reach of small children.
The Sliding roof canopy must be positioned and fixed on a flat level surface.
Do not lean against or push the Sliding roof canopy during construction.
Keep children away from the assemble area.
Do not position your Sliding roof canopy in an area exposed to excessive wind.
Do not attempt to assemble this Sliding roof canopy if you are tired ,have taken drugs or
alcohol or
if you are prone to dizzy spells.
If using a step ladder or power tools ensure that you follow the manufactures safety advice.
Hot items such as recently used grills, blowtorches etc.must not be stores in the Sliding roof
canopy .
Ensure there are no hidden pipes or cables in the ground before inserting the pegs.
GENERAL ADVICE
This is a multi-part assembly, Allow at least 180 minutes for assembly.
Selecting a site-choose a sunny level position away from overhanging trees.
If you are fixing your Sliding roof canopy directly to a solid concrete foundation use
the
pre drilled holes in the metal base supplied.
The component parts should be checked and laid out close at hand.
Keep all small parts(screws etc)in a bowl so they do not get lost.
Note that the door is hinged on the right hand side and therefore opens tothe right.
Keep roof clear of snow and leaves.
CARE & MAINTENANCE
When your Sliding roof canopy needs cleaning, use a mild detergent solution and
risen
with cols clean water.
Do NOT use acetone, abrasive cleaners or other special detergents to clean the
clear panels.
TOOLS & EQUIPMENT REQUIRED
Protective Equipment:
1.Helmet
2.Glove
3.Long Sleeve Cotton Overalls
4.Emergency Medicine Cabinet
5.Eye Shield
Measure (metric):
1.The Tape (5 m)
2.Angle Square
3.Level Meter
-2-
Installation Tool:
1.Triangle Stairs≈
2m Height
2.Spanner 10mm (Ratchet Wrench is better)
3.Spanner 14mm (Install the expansion screw)
4.Hexagon wrench 5mm
5.Electric scre4mm Hexagon wrench
(suggest)
6.Wooden Mallet
7.Marking Pen
8.Percussion bit(8mm and 10mm)
9.Knife
10.Phillips screwdriver
Ø3
Outils de montage :
1. Échelle ≈ 2 m de hauteur
2. Clé de 10 mm (préférable : cliquet)
3. Clé de 14 mm (pour monter la vis d‘expansion)
4. Clé six pans 5 mm
5. Visseuse sans fil + bit de 4 mm pour vis à six pans creux
(recommandé)
6. Maillet
7. Marqueur
8. Burin (8 mm et 10 mm)
9. Cutter
10. Tournevis cruciforme
!
SAFETY ADVICE
We strongly recommend the use of work gloves during assembly.
Do not attempt to assemble the Sliding roof canopy in windy or wet conditions,
Do not touch overhead power cables with the aluminum profiles.
Always wear shoes and safety goggles when working with extruded aluminum.
Dispose of all plastic bags safety-keep them out of reach of small children.
The Sliding roof canopy must be positioned and fixed on a flat level surface.
Do not lean against or push the Sliding roof canopy during construction.
Keep children away from the assemble area.
Do not position your Sliding roof canopy in an area exposed to excessive wind.
Do not attempt to assemble this Sliding roof canopy if you are tired ,have taken drugs or
alcohol or
if you are prone to dizzy spells.
If using a step ladder or power tools ensure that you follow the manufactures safety advice.
Hot items such as recently used grills, blowtorches etc.must not be stores in the Sliding roof
canopy .
Ensure there are no hidden pipes or cables in the ground before inserting the pegs.
GENERAL ADVICE
This is a multi-part assembly, Allow at least 180 minutes for assembly.
Selecting a site-choose a sunny level position away from overhanging trees.
If you are fixing your Sliding roof canopy directly to a solid concrete foundation use
the
pre drilled holes in the metal base supplied.
The component parts should be checked and laid out close at hand.
Keep all small parts(screws etc)in a bowl so they do not get lost.
Note that the door is hinged on the right hand side and therefore opens tothe right.
Keep roof clear of snow and leaves.
CARE & MAINTENANCE
When your Sliding roof canopy needs cleaning, use a mild detergent solution and
risen
with cols clean water.
Do NOT use acetone, abrasive cleaners or other special detergents to clean the
clear panels.
TOOLS & EQUIPMENT REQUIRED
Protective Equipment:
1.Helmet
2.Glove
3.Long Sleeve Cotton Overalls
4.Emergency Medicine Cabinet
5.Eye Shield
Measure (metric):
1.The Tape (5 m)
2.Angle Square
3.Level Meter
-2-
Installation Tool:
1.Triangle Stairs≈
2m Height
2.Spanner 10mm (Ratchet Wrench is better)
3.Spanner 14mm (Install the expansion screw)
4.Hexagon wrench 5mm
5.Electric scre4mm Hexagon wrench
(suggest)
6.Wooden Mallet
7.Marking Pen
8.Percussion bit(8mm and 10mm)
9.Knife
10.Phillips screwdriver
Ø3
F
Summary of Contents for SR-B43
