Konami EVILNIGHT Operator'S Manual Download | Manualshive

Page: 36 / 53

background image

34

7-6 Adjusting the monitor

Monitor adjustment PCB

The monitor has already been adjusted at the time of shipment, but it may be
readjusted as desired.
The monitor adjustment PCB is located inside the service panel. When adjusting
the monitor, open the maintenance door. (See page 12)

1

2

3

4

5

6

7

8

9

CONTRAST

R.GAIN

G.GAIN

B.GAIN

BRIGHT

H.SIZE

H.POSI

V.SIZE

V.POSI

Contrast adjustment

Used to changes the contrast.

Red input gain adjustment

Changes red brightness. Turning it clockwise will make the red deeper.

Green input gain adjustment

Changes green brightness. Turning it clockwise will make the green deeper.

Blue input gain adjustment

Changes blue brightness. Turning it clockwise will make the blue deeper.

Brightness adjustment

Changes brightness. Turning it clockwise will make the image brighter.

Horizontal screen size adjustment

Changes the width of the screen.

Horizontal image position adjustment

Changes the image position in the horizontal direction.

Vertical screen size adjustment

Changes the height of the screen.

Vertical image position adjustment

Changes the image position in the vertical direction.

7 Maintenance

1

2

3

4

5

6

7

8

9

«
...
34
35
36
37
38
...
»

Summary of Contents for EVILNIGHT






















































Reviews:

No comments

Related manuals for EVILNIGHT

OHIO MPQK Lottery Terminal

Brand: Intralot Pages: 36

Golden Tee Fore! Non-Coin-Operated Home Edition

Brand: Chicago Gaming Pages: 27

Brand: Chicago Gaming Pages: 50

Brand: Atronic Pages: 21

ArcadePro Mercury 2097

Brand: Home Leisure Direct Pages: 18

Brand: NAMCO Pages: 29

Brand: Neolt Pages: 114

Brand: Adrenaline Pages: 61

Brand: Envipco Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands