manualshive.com logo in svg

Konami EVILNIGHT, Operator'S Manual

Share
Download
Konami EVILNIGHT Operator'S Manual Download Page 28

26

Caster

Hexagon nut

Adjuster

6-4 Moving the game machine

    How to movement

6 Setting up the game machine

•Before moving the machine, be sure to turn OFF the main power switch

and unplug the power cord.

•Before moving the machine, be sure to fully screw up all the adjusters.

Move the machine on the casters.

•When moving the units, be careful not to apply undue force.
•When moving the machine, do not hold the gun unit or gun cable.
•When the machine has been set up or moved to another place, turn ON

the power switch and press the demagnetizing button on the service panel
to demagnetize the monitor.   If the monitor is still magnetized, the gun
unit may respond well or the target points may get out of position.

1

Be sure to turn OFF the main power
switch and unplug the power cord
from the receptacle.

2

Disconnect the AC power cord from
the machine.

3

Loosen the four adjusters and
move the machine on its casters.

Summary of Contents for EVILNIGHT






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands