Komatsu WA500-6 Shop Manual Download Page 49

Page: 49 / 51

FOREWORD

COATING MATERIALS

WA500-6

00-31

COATING MATERIALS

★

The recommended coating materials prescribed in the shop manuals are listed below.

Category

Code

Part No.

Quantity

Container

Main Applications, Features

hesive

LT-1A

790-129-9030

150 g

Tube

• Used to prevent rubber gaskets, rubber

cushions and cork plugs from coming out.

LT-1B

790-129-9050

20 g

(2 pcs.)

Polyethylene
container

• Used in places requiring an immediately

effective, strong adhesive.

• Used for plastics (except polyethylene,

polypropylene, tetrafluoroethylene, and vinyl
chloride), rubber, metal, and non-metal.

LT-2

09940-00030

50 g

Polyethylene
container

• Features: Resistance to heat, chemicals
• Used for anti-loosening and sealant

purposes for bolts and plugs.

LT-3

790-129-9060
(Set of adhesive
and hardening
agent)

Adhesive:

1 kg

Hardening

agent:

500 g

Can

• Used as adhesive or sealant for metal,

glass, or plastic.

LT-4

790-129-9040

250 g

Polyethylene
container

• Used as sealant for machined holes.

Holtz

MH 705

790-126-9120

75 g

Tube

• Used as heat-resisting sealant for repairing

engine.

Three

bond
1735

179-129-9140

2 g

Polyethylene
container

• Quick hardening-type adhesive.
• Cure time: within 5 sec. to 3 min.
• Used mainly for adhesion of metals,

rubbers, plastics, and woods.

Aron-
alpha

201

790-129-9130

50 g

Polyethylene
container

• Quick hardening-type adhesive.
• Quick cure-type (maximum strength after

30 minutes).

• Used mainly for adhesion of rubbers,

plastics, and metals.

Loctite

648-50

79A-129-9110

50 cc

Polyethylene
container

• Features: Resistance to heat, chemicals
• Used at joint portions subject to high

temperature.

Gasket

sealant

LG-1

790-129-9010

200 g

Tube

• Used as adhesive or sealant for gaskets and

packing of power train case, etc.

LG-3

790-129-9070

1 kg

Can

• Features: Resistance to heat
• Used as sealant for flange surfaces and

bolts at high temperature locations; used to
prevent seizure.

• Used as sealant for heat-resistant gasket for

high-temperature locations such as engine
precombustion chamber, exhaust pipe.

Summary of Contents for WA500-6




















































Search results

Summary of Contents for WA500-6

Reviews:

Related manuals for WA500-6

Brands by name

Popular brands

Komatsu WA500-6, Shop Manual

Search results

Summary of Contents for WA500-6

Reviews:

Related manuals for WA500-6

Brands by name

Popular brands