Komatsu WA500-6 Shop Manual Download Page 39

Page: 39 / 51

FOREWORD

HANDLING ELECTRIC AND HYDRAULIC EQUIPMENT

WA500-6

00-21

Handling Connectors Used for Engines

The following engines use the connectors described in this section.

•

95E-5

•

107E-1

•

114E-3

•

125E-5

•

140E-5

•

170E-5

•

12V140E-3

★

Your machine has a 140E-5 diesel engine.

Slide Lock Type

FRAMATOME-3, FRAMATOME-2

★

95 – 170, 12V140 engines

•

Pressure sensors and NE speed sensor

Disconnect connector (1) according to the following procedure.

Slide lock (L1) to the right.

While pressing lock (L2), pull out connector (1) toward you.

Even if lock (L2) is pressed, connector (1) cannot be pulled toward
you if part A does not float. In this case, float part A with a small
screwdriver while pressing lock (L2), and then pull out
connector (1) toward you.

Engine

Sensor

125, 170, 12V140

Intake air pressure sensor in intake manifold: PIM

125, 170, 12V140

Oil pressure sensor: POIL

95, 107, 114

Oil pressure switch

95 – 170, 12V140

Ne speed sensor of flywheel housing: NE

125, 170, 12V140

Ambient pressure sensor: PAMB

Summary of Contents for WA500-6




















































Search results

Summary of Contents for WA500-6

Reviews:

Related manuals for WA500-6

Brands by name

Popular brands

Komatsu WA500-6, Shop Manual

Search results

Summary of Contents for WA500-6

Reviews:

Related manuals for WA500-6

Brands by name

Popular brands