Komatsu WA500-6 Shop Manual Download Page 38 | Manualshive

Page: 38 / 51

background image

FOREWORD

HANDLING ELECTRIC AND HYDRAULIC EQUIPMENT

00-20

WA500-6

6.

Flushing operations

After disassembling and assembling the equipment, or changing
the oil, use flushing oil to remove the contaminants, sludge, and
old oil from the hydraulic circuit. Normally, flushing is carried out
twice: primary flushing is carried out with flushing oil, and
secondary flushing is carried out with the specified hydraulic oil.

7.

Cleaning operations

After repairing the hydraulic equipment (pump, control valve, etc.)
or when running the machine, carry out oil cleaning to remove the
sludge or contaminants in the hydraulic oil circuit. The oil cleaning
equipment is used to remove the ultra fine (about 3 µ) particles that
the filter, built in the hydraulic equipment, cannot remove; it is an
extremely effective device.

«
...
36
37
38
39
40
...
»

Summary of Contents for WA500-6




















































Reviews:

No comments

Related manuals for WA500-6

Brand: jcb Pages: 208

Brand: Wacker Neuson Pages: 19

Brand: Xtreme Manufacturing Pages: 74

Telehandler TH412

Brand: Wacker Neuson Pages: 362

Brand: jcb Pages: 51

LOADER 4211 MSL

Brand: RHINO Pages: 104

Brand: Oshkosh Corporation Pages: 171

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands