Kolver ACE Screw Counter Operator'S Handbook Manual Download Page 11

Page: 11 / 12

Warning: Do not connect buttons or other systems (for example remote systems such as PLC) with
external voltage and/or earth. Refer only to the figure 5.2.
Any tampering or damage caused by improper use of the device are not covered by warranty.

It’s possible to stop by remote the fastening cycle through a contact available on the back panel.

Closing this contact, the cycle is blocked and also the screwdriver. Useful as a part present on your
assembly line.

Fig. 5.3 Connection keyboard

–

part present

Technical features:

Transformer

12VDC 200mA

Nominal current

230mA

Max current

500mA

Keyboard Relay:

Nominal voltage

Pick-up Voltage
VDC

Drop-out Voltage
VDC

Max. allowable Voltage
VDC (at 20 )

18.0

1.20

31.2

Summary of Contents for ACE Screw Counter













Search results

Summary of Contents for ACE Screw Counter

Reviews:

Related manuals for ACE Screw Counter

Brands by name

Popular brands

Kolver ACE Screw Counter, Operator'S Handbook Manual

Search results

Summary of Contents for ACE Screw Counter

Reviews:

Related manuals for ACE Screw Counter

Brands by name

Popular brands