background image

9

5.  Do not connect directly to an electrical outlets or car 

cigarette lighter sockets.

6.  Do not use the battery for a purpose other than those 

speci

fi

 ed.

7.  If the battery charging fails to complete even when a 

speci

fi

 ed recharging time has elapsed, immediately stop 

further recharging.

8.  Do not put or subject the battery to high temperatures or 

high pressure such as into a microwave oven, dryer, or 

high pressure container.

9.  Keep away from 

fi

 re immediately when leakage or foul 

odor are detected.

10. Do not use in a location where strong static electricity 

generates.

11. If there is battery leakage, foul odor, heat generated, 

discolored or deformed, or in any way appears abnormal 

during use, recharging or storage, immediately remove it 

from the equipment or battery charger, and stop use.

12. Do  not immerse the battery or allow any 

fl

 uids  to 

fl

 ow 

inside. Conductive liquid ingress, such as water, can 

cause damage resulting in 

fi

 re or explosion. Store your 

battery in a cool, dry place, away from combustible and 

fl

 ammable items. Corrosive gas atmospheres must be 

avoided.

CAUTION

1.  If liquid leaking from the battery gets into your eyes, 

do not rub your eyes and wash them well with fresh 

clean water such as tap water and contact a doctor 

immediately.

 

If left untreated, the liquid may cause eye-problems.

2.  If liquid leaks onto your skin or clothes, wash well with 

clean water such as tap water immediately.

 

There is a possibility that this can cause skin irritation.

3. If you 

fi

 nd rust, foul odor, overheating, discolor, 

deformation, and/or other irregularities when using the 

battery for the 

fi

 rst time, do not use and return it to your 

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium 

ion battery, the battery may be shorted, causing 

fi

 re. When 

storing the lithium ion battery, obey surely the rules of 

following contents.

  Do not place conductive debris, nail and wires such as 

iron wire and copper wire in the storage case.

  To prevent shorting from occurring, load the battery in 

the tool or insert securely the battery cover for storing 

until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY 

TRANSPORTATION

When transporting a lithium-ion battery, please observe the 

following precautions.

WARNING

Notify the transporting company that a package contains a 

lithium-ion battery, inform the company of its power output 

and follow the instructions of the transportation company 

when arranging transport.

  Lithium-ion batteries that exceed a power output of 

100 Wh are considered to be in the freight classi

fi

 cation 

of Dangerous Goods and will require special application 

procedures.

 For transportation abroad, you must comply with 

international law and the rules and regulations of the 

destination country.

Wh

Power Output

2 to 3 digit number

NAMES OF PARTS (Fig. 1–Fig. 10)

Battery

Latch

Motor

Pilot lamp

Nameplate

Wrench (small)

Nose bracket

Wrench (large)

Collet chuck

Wheel

Spindle

Tapared portion

Front cover

Interior protrusions 

(2 locations)

Switch knob

Side handle

Dial 

Filter

SYMBOLS

WARNING

 

The following show symbols used for the machine. 

Be sure that you understand their meaning before 

use.

GP18DA:  Cordless Die Grinder

To reduce the risk of injury, user must read 

instruction manual.

Always wear eye protection. 

Only for EU countries 

Do not dispose of electric tools together with 

household waste material!

In observance of European Directive 

2012/19/EU on waste electrical and electronic 

equipment and its implementation in 

accordance with national law, electric tools 

that have reached the end of their life must 

be collected separately and returned to an 

environmentally compatible recycling facility.

V

Rated voltage
Direct current

n

0

No-load speed

n

Rated speed

min

-1

  Revolution or reciprocations per minute 

Disconnect the battery

00Book̲GP18DA̲UK.indb   9

00Book̲GP18DA̲UK.indb   9

2021/03/04   15:38:10

2021/03/04   15:38:10

Summary of Contents for Hikoki GP 18DA

























Reviews: