background image

1237458-T01-A

-11-

TROUBLESHOOTING

No flushing

1. No power or mistake connected.
2. Not able to detect the urine.
3. Out of electricity.

1. Check the power connect.
2. See user's guide.
3. Replace batteries.

Please make following checks before repair:

Symptoms

Probable causes

Corrective actions

No flashing

1. The small hole of valve core is blocked.

2. The filter of valve core is blocked.

1. Clean the small hole of valve core with

thin steel wire.

2. Wash the filter of valve core with a brush.

If the trouble remains after above-mentioned actions are taken, please contact with us via distributor.

No flushing or poor
flushing

1. Adjusting bolt not fully open
2. Low water pressure.
3. Filter is obstructed.

1. Open the adjusting bolt.
2. Improve water supply.
3. Clean the filter.

1.
2.
3.

1.
2.

1.
2.
3.

1.
2.

1.
2.
3.

1.
2.
3.

IMPORTANT CONSUMER INFORMATION

Consumer Responsibilities

1. Do not directly flush the sensor with water. The sensor is

an electronic instrument.

2. Keep away from strong electromagnetic field.

3. Clean the urinal with soft rag and neutral liquid detergent.

Do not use eradicator, abrasive powder or oil, acid or
alkali liquid detergent.

4. Urinal is designed for use with potable water. Avoid water

that includes a lot of contaminants or acid/alkali water and
impure water.

5. All electrical connection must be compliance with related

regulation and codes.

6. All installation staff should be well familiar with installation

instruction.

WARNING

WARNING: Risk of product damage.

Never spit phlegm and throw stub or

something else into the urinal.
Please avoid using articles either dissolvable or with
the diameter smaller than 5mm, such as moth ball.

Do not throw into the urinal what is easy to block it,
such as newspaper, paper pilch.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.

o

CAUTION:

Please do not use hard materials (like

scouring pad) to clean product surface, especially the
product logo.

1.

2.

3.

4.

5.

6.

5mm

0 C

o

Summary of Contents for STRUKTURA K-5888T












Reviews: