Kohler rada Thermotap-3 Product Manual Download Page 14 | Manualshive

Page: 14 / 24

background image

14

1058907-W2-J

The Rada Thermotap-3 has a single lever that provides sequential operation from

OFF through COLD and

WARM to a preset maximum blend temperature.

The

maximum temperature is preset to approximately 41°C under ideal installation

conditions at the factory.

To change this setting refer to the information given in

section:

Commissioning'

.

OPERATION

Principle of Operation

Off

Warm

Cold

Preset

Maximum Blend

Temperature

«
...
12
13
14
15
16
...
»

Summary of Contents for rada Thermotap-3

























Reviews:

No comments

Related manuals for rada Thermotap-3

Brand: Zoeller Pages: 38

Brand: unidrain Pages: 56

Brand: Franke Pages: 20

Brand: Brizo Pages: 8

Brand: Hans Grohe Pages: 40

Brand: Alder Pages: 2

Brand: Majestic Pet Pages: 2

Brand: Pulse Shower Spas Pages: 8

Talis M54 72804 Series

Brand: Hans Grohe Pages: 56

Brand: hernest Pages: 4

LIS CW1 H894660

Brand: Laufen Pages: 8

Brand: Olympia Pages: 2

Metris 31471000

Brand: Hans Grohe Pages: 24

Refinia K-T5324

Brand: Kohler Pages: 20

Metropol 32511 1 Series

Brand: Hans Grohe Pages: 16

BAGNODESIGN KOY BDM-KOY-410 Series

Brand: Sanipex Pages: 8

AQUAECO AQM-EX3-410-BS

Brand: Sanipex Pages: 8

Brand: Sanela Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands