Kohler PRO 3.7 Owner'S Manual Download Page 14

10

 

 

 

TP-7213  7/21

 

8.6 Oil 

Recommendations 

All-season KOHLER

®

 PRO 10W-50 Synthetic Oil is the ideal 

oil for KOHLER engines. It is speci

fi

cally formulated to 

extend the oil change interval to 300 Hours. Contact your 
Kohler authorized dealer for availability. 
300-Hour oil change intervals are exclusive to and only 
authorized on KOHLER engines that utilize the KOHLER 
PRO 10W-50 Synthetic Oil. Alternative engine oils may be 
used with KOHLER engines but require 100-Hour oil change 
intervals for proper maintenance. Oil must be API (American 
Petroleum Institute) service class SJ or higher. Select 
viscosity based on air temperature at time of operation as 
shown in Figure 2. 

 

 

Figure 2 

Oil Recommendations 

8.7 Fuel 

Recommendations 

E15, E20 and E85 are NOT approved and should NOT be used; effects of old, stale or contaminated fuel are not warrantable. 

Fuel must meet these requirements: 

 

Clean, fresh, unleaded gasoline. 

 

Octane rating of 87(R+M)/2 or higher. 

 

Research Octane Number (RON) 90 octane minimum. 

 

Gasoline up to 10% ethyl alcohol, 90% unleaded is acceptable. 

 

Methyl Tertiary Butyl Ether (MTBE) and unleaded gasoline blend (max 15% MTBE by volume) are approved. 

 

Do not add oil to gasoline. 

 

Do not overfill fuel tank. 

 

Do not use gasoline older than 30 days. 

 

8.8 Circuit 

breaker 

Generator set's electrical circuit is protected by one or more magnetothermal, differential or thermal cut-out switches. If an overload 
and/or short circuit occurs, supply of electrical energy may be cut. 
If necessary, replace circuit breaker (A) in generator set with circuit breakers with identical nominal ratings and specifications. 

 

8.9 

DisCOver – Carbon Monoxide (CO) Shutdown System 

CO Sensor automatically shuts down the engine when harmful levels of carbon monoxide accumulate around the generator or a 
CO sensor fault occurs. After shutdown, the CO sensor indicator light (A16) will blink for at least five minutes per the chart below. 

CO sensor DOES NOT replace carbon monoxide alarms. 
Install battery-powered carbon monoxide alarm(s) in your home. Don’t run generator in enclosed areas. 

Color Description 

Red 

Carbon monoxide accumulated around the generator. Prior to restarting move the generator to an open, outdoor area 20 ft. (6 
m) from occupied spaces with exhaust pointed away. Air out premises (open windows and doors) before reoccupying property. 
Automatic shutoff is an indication generator was improperly located. 
If you start to feel sick, dizzy, weak, or your home’s carbon monoxide alarm sounds while using this product, get to fresh air 
right away. Call emergency services. You may have carbon monoxide poisoning. 

Yellow 

CO Sensor fault occurred.* 

* Yellow light will blink for five seconds at the startup of the generator to show the CO sensor functioning properly. 

 

8.10 Specifications 
Specifications 

Model PRO 

3.7 

Overall Dimensions  
(L x W x H) 

24.8 in. (630 mm) x 
19.6 in. (498 mm) x 

20.6 in. (523 mm) 

Dry Weight 

133.6 lbs. (60.6 kg) 

AC Rated Power 

3000 

Watt 

(120 Volts x  

25.0 Amps) 

(240 Volts x  

12.5 Amps) 

AC Maximum Power 

3700 

Watt 

(120 Volts x  

30.8 Amps) 

(240 Volts x  

15.4 Amps)

 

DC Rated Power 

100 Watt (12 Volts x 8.3 Amps) 

Bore 

2.8 in. (70 mm) 

Stroke 

2.1 in. (54 mm) 

Displacement 

12.7 cu. in. (208 cc) 

Oil Capacity (Refll) 

0.63 U.S. qt. (0.60 L) 

Maximum Angle of Operation (@ full oil level)* 

25° 

Run Time 

>8 hours (50% load) 

Fuel 

See Fuel Recommendations section 

Fuel Tank Capacity 

3.4 gal. (13.0 L) 

Spark Plug Gap 

0.03 in. (0.76 mm) 

* Exceeding maximum angle of operation may cause engine damage from insufficient lubrication. 
Additional specification information can be found at KohlerPower.com. 

°F -20

0

20

32 40

60

50

80

100

°C -30

-20

-10

0

10

20

30

40

 5W-30

10W-30

SAE 30

Summary of Contents for PRO 3.7





























Reviews: