Kohler K-4026T Installation Instructions Manual Download Page 13

Page: 13 / 18

-13-

NOTE:

If the wall for installation is made of special material

(such as wood board, density board and etc.), suitable fixing
methods shall be adopted.

The place to install the remote controller shall not be

easily splashed by water.

Choose a mounting location for the remote holder that is
easily accessible while sitting on the seat.

Drilling two holes with depth larger than 45mm on the wall by
drill with a diameter of 6mm in accordance with the position of
screw holes on the remote control holder. Installing the
expansion tube into the holes.

Placing the installation holder on the fixing hole.

Peeling off the release paper of double-sided tape at the back
of holder.

Fixing the holder with screws and install it.

Installing the screw covers on the screws.

Placing the remote controller on the holder.

6mm

45mm

Fig.#23

Fig.#22

45mm

Expansion Tube

Remote Holder

Double-Sided Tape

Expansion Screw

Screw Cover

Remote Controller

INSTALLATION OF REMOTE CONTROLLER HOLDER

Installation Steps:

1144585-T01-A

Summary of Contents for K-4026T



















Search results

Summary of Contents for K-4026T

Reviews:

Related manuals for K-4026T

Brands by name

Popular brands

Kohler K-4026T, Installation Instructions Manual

Search results

Summary of Contents for K-4026T

Reviews:

Related manuals for K-4026T

Brands by name

Popular brands