background image

Page 1

Before installing the shower please read these instructions carefully to familiarise
yourself with the required tools, materials and installation sequences. Please leave these
instructions for the consumer after installation. Refer to the separate care and maintenance
guide for important care and cleaning information.  

Ensure that the shower tray and wall, if applicable, are completely finished prior to
installing your shower door and return. Follow all warnings, cautions and instructions
contained in this guide.  

1.   ENGLEFIELD strongly recommends that a minimum of TWO persons install this
      enclosure due to the weight of the door panels. 

2.   Toughened safety glass cannot be cut. Risk of injury or product damage. 

3.   Wear protective footwear when lifting panels. 

4.   Wear safety glasses when drilling. 

1.   The wall retainers must be installed onto a waterproof, vertical and flat wall surface.    
      Failure to do so will result in an unsatisfactory seal, which may cause property damage.
      The wall inclination (out of squareness) is recommended to be out by no more than

      +/- 4mm/m.

   

2.   Please install this door onto an ENGLEFIELD Quick - Fit   Low Profile
      shower tray only, unless installing directly onto tiled walls and floor.

®

 
 

3.   Care must be taken when drilling into walls and floors to avoid any hidden pipes or
      wires. 

4.   It is the responsibility of the INSTALLER to ensure that the installation complies with 
      council and or local authority bylaws.

INSTALLATION INSTRUCTIONS

VALENCIA ELITE

Square Sliding

BEFORE YOU BEGIN

SAFETY 

!

!

ATTENTION

Instructions, drawings, and diagrams contained in this manual present information available at the time of printing. 

changes without further notice.

ENGLEFIELD

Summary of Contents for Englefield Valencia Elite















Reviews: