background image

-14-

(RCD)

RCD

RCD

RCD

RCD

RCD

RCD

·

·

·

·

·

·

CAUTION: Risk of personal injury.

To reduce

the risk of injury, people with infirmities should
not be allowed to use this product without close,
continuous supervision.

Use this bath only for its intended purpose as
described in this guide. Do not use attachments not
recommended by Kohler Co.
The bath must be connected only to a supply circuit
that is protected by a Residual Current Device
(RCD). Such a RCD should be provided by the
installer and should be tested on a routine basis. To
test the RCD, press the test button. The RCD
should interrupt power. Press the reset button.
Power should be restored. If the RCD fails to
operate in this manner, the RCD is defective. If the
RCD interrupts power to the bath without the test
button being pressed, a ground current is flowing,
indicating the possibility of an electric shock. Do not
use this bath. Disconnect the bath and have the
problem corrected by a qualified service
representative before using.
Flush your whirlpool system twice a month or more
depending upon usage, as described in the "Flush
the System" section of this guide.
Do not operate this unit without the guard (cover)
over the suction fitting.
Repeated use of personal care products containing
oils can damage plastic whirlpool components.
Avoid using bath oils.
Whirlpool hydro-massage action can cause even a
small amount of bubble bath, bath soap, shampoo,
or bath oil to foam excessively. For this reason,
please do not use these products during whirlpool
operation.

·

·

·

·

·

·

OPERATING THE AIR SYSTEM

·

·

·

·

·

4"

102 mm

·

NOTE:

NOTE:

This is a combination airbath and whirlpool

bath, and includes a heated back surface. For
information on using the whirlpool features, refer to the
"Operating the Whirlpool System" section. Refer to the
"Operating the Heated Surface" section to use the
heated surface feature.

If the unit does not function properly, please

refer to the "Troubleshooting" section.

Before entering the bath, make sure the seal is free
of dirt and debris.
Enter the bath, then close and latch the door.
Use your hand to test the water temperature before
closing the drain and filling the bath.
Fill the bath at least 4" (102 mm) above the top of
the airjets.
Press the three-speed air system button once to
start the air system at high speed.
Press the air system button a second time to
operate the air system at medium speed.

·

·

·

·

·

·

1397340-T01-A

Summary of Contents for BELAY K-156T-LCP























Reviews: