7
1418436-T01-A
1.
感应指示灯的各种闪烁情况
感应指示灯是使用者了解感应龙头
有效、唯一的途径。所以明白了感
应指示灯闪烁所代表的含义，可以
正确使用感应龙头，如图示：
(1)
快速闪烁，代表感应龙头正处于
通电后的两分钟自动调节阶段。期
间，安装者、使用者不得干扰其自
动调节，感应范围内不要放置物体。
(2)
间隔约
6
秒钟闪烁一次：代表龙
头电池即将耗尽，提醒用户马上更
换电池。
(3)
间隔约
2
秒钟连续闪烁：代表龙
头电池耗尽，已停止工作，等待使
用者更换电池。
(4)
在正常工作情况下，当有物体被
感应时，龙头出水，感应指示灯闪
烁一次。（龙头关闭，感应指示灯
不闪烁。）
2.
把手的操作
面对水龙头，轻轻向前推动把手，
向红标方向转动为热水，向蓝标方
向转动为冷水。
3.
超时出水控制
龙头感应出水后，如不再次感应止水，则龙头连
续出水
4
分钟后，龙头自动止水。再次感应后，
龙头正常出水，否则无反应。
用户须知
指示灯
适用于所有加工处理过的表面，以中性肥皂水清
洗镀层表面，再以干净的软布彻底擦干整个表面。
许多清洁剂，比如氨水，去污粉及洁厕灵等，会
对电镀表面造成伤害，切忌使用。
有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙
头及其配件上。
保持感应窗口清洁，可用蘸有中性清洁剂的软布
擦洗。
注意
a.
禁止使用去污粉、研磨粉及油类、酸性类、碱
性类清洁剂。
b.
禁止直接对感应窗口喷洒空气清新剂、清毒液
或其他除臭、清洁类有机溶剂。
c.
勿撞击感应窗口。
清理说明
Applicable to all finished surface, clean coated surface with
neutral soap water, and then wipe entire surface with clean
soft cloth. Do not use detergents, such as ammonia, clean-
ing powder and toilet cleaner etc. those detergents will
cause plated surface damage. Do not use.
Do not apply corrosive detergent or solvents on KOHLER
faucet and fittings.
Keep sensing eye clean. Use a soft rag or sponge with
neutral detergent to clean the product.
Note:
a. Do not use detergent, abrasive cleaners, acid and
alkaline detergent.
b. Do not spray air freshener, disinfectant or other deodoriz-
ing and organic solvents on the sensing eye.
c. Do not impact sensing eye.
CLEANING INSTRUCTION
1. Various flashing condition of sensor
Sensor is the effective and only way for
customer to understand the induction faucet.
Understand the meaning of sensor flashing
will help customer use induction faucet
properly as shown:
(1) Quick flash indicates induction faucet is
in 2 minutes automatic adjusting cycle. The
area in front of the sensor must be free of
objects; installer and user shall not disturb
automatic adjustment cycle.
(2) Flash once approximately every 6
seconds: indicates faucet battery is about to
run out. Remind customer to replace the
batteries immediately.
(3) Flash continuously approximately every
2 seconds: indicates faucet battery is about
to run out and wait for customer to replace
the batteries.
(4) Under normal working condition, when
approaching the sensing distance, water
flow from faucet, sensor flash once. (Faucet
turns off, sensor does not flash).
2. Handle operation
Stand in front of faucet, push the handle
forward slightly. Turn it to red label direction
for hot water and turn it to blue label direction
for cold water.
3. Overtime water flow control
After water flowing from faucet, the water will run 4 minutes
continuously if the faucet does not sense the water stop
action. After sensing the action, water flow out properly;
otherwise there will be no reaction.
CUSTOMER INSTRUCTION
Sensor
