4
1418436-T01-A
3
、控制阀组件的安装固定
用内六角扳手拧下阀盒盖螺钉
(30)
，
将阀盒盖
(29)
打开。根据安装尺寸图
确定控制阀组件
(28)
安装位置，打孔，
打入膨胀管
(31)
，使阀盒紧贴墙面且
控制阀向上，再用膨胀螺钉
(32)
将控
制阀组件固定在墙壁上，注意控制
阀组件要与墙面保持平行。
4
、如何安装感应组件
将垫片
(34)
装入感应组件
(33)
底部凹
槽中，将带有垫片的感应组件插入
台面安装孔中，调整感应组件挥手
标识在正上方。
从台面下方依次将垫片
(36)
、垫片
(37)
和安装环
(38)
装入本体
(35)
，旋
上安装环，锁紧螺钉
(39)
以固定感应
组件。
感应组件的线
(40)
与控制阀组件内的
插头连接。
36
35
40
34
33
37
39
38
5
、如何安装把手组件
将垫片
(34)
装入把手组件
(41)
底部凹
槽中，将带有垫片的把手组件插入
台面安装孔中，调整把手，使把手
上的红点在左边，蓝点在右边。
从台面下方依次将垫片
(36)
、垫片
(37)
和安装环
(38)
装入本体
(42)
，旋
上安装环，锁紧螺钉
(39)
以固定把手
组件。
把接头
(55)
带垫片
(56)
接到水源，然
后将进水软管与接头相连，带有红
点标签的软管接热水，带有蓝点标
签的软管接冷水。将另一根软管
(43)
连接控制阀体组件进水端。
42
36
41
34
37
38
44
39
43
55
56
3. Control valve assembly installation
Hex wrench unscrew valve cover bolts (30)
and open valve cover (29). Drill installation
hole and insert expansion pipe (31) per
control valve assembly (28) position speci-
fied in rough-in. Make sure valve box against
the wall and control valve upwards. Secure
control valve assembly on the wall by expan-
sion screws (32), make sure control valve
assembly is paralleled to the wall.
4. How to install the sensor assembly
Install washer (34) into the bottom groove of
the sensor assembly (33), then insert the
sensor assembly with washer into mounting
hole on the wash basin, adjust the sensor
assembly waving mark on the top.
From under the wash basin, slide the washer
(36), washer (37) and installation ring (38)
into main body (35). Secure installation ring,
locking screw (39) on the sensor assembly.
Connect the sensor assembly wire (40) to
plug inside the control valve assembly.
5. How to install handle assembly
Slide washer (34) into the bottom groove of
handle assembly (41), insert handle assem-
bly with washer into mounting hole on the
wash basin. Adjust handle so to set the red
dot on the left side and blue dot on the right
side.
From under the wash basin, slide washer
(36), washer (37) into main body (42), screw
installation ring and locking screw (39) in to
secure handle assembly.
Connect connector (55) with washer (56) to
water supply and then connect water inlet
hose to connector. Connect hot water to flex
hose with red dot label, cold water to flex
hose with blue dot label. Connect another
flex hose (43) to water inlet end of control
valve assembly.
28
29
30
28
31
32