Kohler 12RESL Operation Manual Download Page 21

TP-6517 1/11

21

Section 3 Scheduled Maintenance, 12 kW Models

Section 3 Scheduled Maintenance, 12 kW Models

Accidental starting.
Can cause severe injury or death.

Disconnect the battery cables before
working

on

the

generator

set.

Remove the negative (--) lead first
when

disconnecting

the

battery.

Reconnect the negative (--) lead last
when reconnecting the battery.

WARNING

Disabling the generator set.

Accidental starting can

cause severe injury or death.

Before working on the

generator set or connected equipment, disable the generator
set as follows: (1) Move the generator set master switch to the
OFF position.

(2) Disconnect the power to the battery

charger. (3) Remove the battery cables, negative (--) lead
first. Reconnect the negative (--) lead last when reconnecting
the battery. Follow these precautions to prevent starting of the
generator set by an automatic transfer switch, remote
start/stop switch, or engine start command from a remote
computer.

Hot engine and exhaust system.
Can cause severe injury or death.

Do not work on the generator set until
it cools.

WARNING

Servicing the exhaust system.

Hot parts can cause

severe injury or death.

Do not touch hot engine parts. The

engine and exhaust system components become extremely
hot during operation.

Hazardous voltage.
Can cause severe injury or death.

Operate the generator set only when
all guards and electrical enclosures
are in place.

Moving parts.

WARNING

Servicing the generator set when it is operating. Exposed
moving parts can cause severe injury or death.

Keep

hands, feet, hair, clothing, and test leads away from the belts
and pulleys when the generator set is running.

Replace

guards, screens, and covers before operating the generator
set.

3.1 Routine Maintenance

Refer to the following service schedule and the runtime
hours displayed on the controller display to schedule
routine maintenance. Have an authorized distributor/
dealer service the generator set at the designated
intervals in the service schedule for the life of the
generator set. Service units subject to extreme weather,
long operating hours, or dusty or dirty conditions more
frequently.

Contact an authorized distributor/dealer for parts.

Summary of Contents for 12RESL

















































Reviews: