Kohler 10EOZ Manual Download Page 43

Page: 43 / 80

TP-6053 7/04

Section 6 Controller Troubleshooting

Is there AC output
when the start button
is HELD and the unit
is running?

Is AC output at the
correct voltage
(e.g. 120 volts AC)?

Yes

Test the
voltage
regulator.

Replace the
controller circuit
board.

Yes

Is there 12VAC output at the
B1/B2 stator winding?

Test the stator,
main field (rotor) and
exciter/armature.

Yes

Is there 12VDC at
the exciter field?

Yes

Test the stator,
and the main
field.

Separately excite the
generator set to
determine if other
components are
inoperative.

Replace the
controller
circuit
board.

Yes

Test the
voltage
regulator.

Is AC output voltage at
spec.? (See Section 7.3,
Separate Excitation).

Test the stator, main
field (rotor), and
exciter/armature.

Is the voltage
regulator
fuse okay?

Yes

Replace the
fuse.

(OPTIONAL)

Go to B at the beginning
of the preceding page.

Figure 6-7

Troubleshooting Relay Controller Circuit Board (4 of 4)

Summary of Contents for 10EOZ

















































































Search results

Summary of Contents for 10EOZ

Reviews:

Related manuals for 10EOZ

Brands by name

Popular brands

Kohler 10EOZ, Manual

Search results

Summary of Contents for 10EOZ

Reviews:

Related manuals for 10EOZ

Brands by name

Popular brands