Koei Unic - 05 Operation Manual Download Page 15

-12- 

Valve Position Indicator 

Limit Dog 

Limit Dog Screw 

Position Indicator Screw 

Sleeve Screw 

 Dog Screw 

Output Shaft 

Sleeve 

[ Unic-20, -40 ] 

 

 

[Fig.13] 

8-2 Potentiometer resistance output (option) 

[Fig.14] 

a) Remove top cover.

See switches and dogs in the left (Fig.13).

b) Switches are arranged in the left and right. The right

are for close, left are for open.

(Upper for contact output)

c) Manually set the opening at 1/2 ~1 handle turn

before stop position.

d) Loosen dog screw and fix the switch at the position it

clicks.

*Adjust both right and left (open and close).

e) After the adjustment, confirm that the switches

function just before stop position.

f) Loosen dial plate screw and fix it at the set opening.

Potentiometer  

Position Indicator Screw 

 Valve Position Indicator 

Sleeve  

Sleeve Screw 

Dog Screw 

Limit Dog 

Output Shaft 

 Opening Spur Gear 

Gear Screw 

Gear Screw 

Potentio Spur Gear 

a) Remove actuator top cover (Electric unit cover).

Potentiometer is connected with gears as shown in
[Fig.14].

b) Potentiometer is available with 135

, 500

, 1K

for users choice.

c) Set the opening manually at “ Full close ”.
d) Apply a tester between terminals 4 and 5, and loosen

sleeve screw for turn. Set the potentiometer at a
desired resistance, then, screw it up. Adjustment is
now over.

Make sure that the position switch (stop) functions
in position.

e) Confirm the resistance at full close and full open that

output resistance is within the range.

f) Finally, loosen dial plate and fix it at the set opening.

Potentiomete

Summary of Contents for Unic - 05




















Reviews: