background image

10

Basic Maintenance 

– continued

Connections

Connections on hoses, the gun/lance assembly 
and spray lance should be cleaned regularly and 
lubricated with lithium grease to prevent leakage 
and damage to the O-rings.

Water Screen

 

CAUTION: 

If the screen is not kept clean, the 

  flow of water to the pressure washer will be 
  restricted and the pump may be damaged.

The pressure washer is equipped with a water 
inlet screen to protect the pump. Clogging of the 
water screen will restrict flow of water. Cleaning 
is immediately required with unit turned OFF.

  1. Disconnect the garden hose from the INLET.
  2. Remove the water screen from the INLET.
  3. Clean screen under warm water.
  4. Replace screen immediately to prevent any 
 

 foreign matter from entering the pump.

  5. Reconnect the garden hose to the INLET.

 CAUTION: 

Do not damage the screen while 

  removing or cleaning. Any foreign particles 
  entering the pump will damage the unit.

Pump Oil Change

 

NOTE: 

The pump of the pressure washer will 

  require an oil change once a season or after 
  every 50 hours of operation. Use only SAE30 
  non-detergent oil in the pump. 

To change the oil in the pump, the unit needs to 
be tipped on its side. As a result of this the engine 
oil should be changed at the same time. This will 
avoid flooding the engine with oil when the unit is 
tipped sideways.

 NOTE: 

Refer to the Engine Owner's Manual 

  for details on changing the engine oil.

 Step 1.

 Remove gasoline from engine.

 

Step 2.

 Drain engine oil. Refer to the Engine 

 

 Owner's Manual for details.

 Step 3.

 Gently tip the unit sideways so that the 

 

 oil drain/fill plug is facing upward.

 Step 4.

 Remove oil drain/fill plug from pump, then 

 

 gently tip the unit in the opposite direction

 

 until the oil is drained from the pump.

 

 Please dispose of oil properly.

 

Step 5.

 Once oil is drained, gently tip unit so that 

 

 the drain/fill hole faces up and add new 

 

 oil to chamber. Do not overfill. Use 0.13 L 

 

 of SAE30 non-detergent motor oil. 

 Step 6.

 Replace oil drain/fill plug, secure firmly 

 

 and tip unit upright.

 Step 7.

 Replace engine oil. Refer to the Engine 

 

 Owner's Manual for details.

Engine

To ensure proper care of the engine, be sure to 
follow the manufacturer's maintenance schedule, 
routine inspection procedures, and maintenance 
procedures.

Please refer to the Honda Engine Owner's Manual 
for details on maintenance of the engine.

 

WARNING: 

Improperly maintaining the engine, 

  or failure to correct a problem before operation, 
  can cause a malfunction in which you can be 
  seriously hurt or killed.

 NOTE: 

In the unlikely event that you have a 

  problem with the engine, you must contact a 
  Honda Service Centre. Please call the Honda 
  toll-free hotline at 

1-888-946-6329 

to locate the 

  nearest Authorized Service Centre.

 

Summary of Contents for CG2600T















Reviews: