9
KOBRA AF.1 e Kobra AF+1 Manuale
-AUTOMATIC STOP If the bag is full or the door is open with
red warning light flashing (I).
- ENERGY SMART SYSTEM which automatically reduces
power consumption when on STAND-BY and when 12
seconds have passed since the last automatic shred cycle.
CARE AND MAINTENANCE
The Kobra AF.1 and KOBRA AF+1 I are high quality shredders,
designed for automatic and manual shredding.
The cutting knives of the Kobra AF1 C4 and Kobra AF+1 C4
do not need to be lubricated with oil. However to maintain
your shredder in optimum condition, you must use it
responsibly and periodic maintenance is recommended.
The Kobra AF.1 C2 is fitted with a special integrated oiling
system, the ”AUTOMATIC OILER” which eliminates the need
for oiling the cutting knives manually so it is advisable to
periodically check the level of the oil in the container inside
the cabinet.
It is not normally necessary to operate the machine at
maximum capacity every time it is used.
It is always recommended to use the machine at less than
maximum capacity.
This will mean you need less frequent maintenance and will
prolong the life of mechanical parts.
ATTENTION!
In case of slippage or failure to pull the paper through
the machine, the 8 inlet belts in the feeder tray should
be cleaned regularly with a soft damp cloth.
AUTOMATIC OILER (FIg.2)
(only for the model Kobra AF.1 C2)
The Kobra AF.1 C2 is fitted with a special integrated oiling
system, the ”AUTOMATIC OILER” which eliminates the need
for oiling the cutting knives,
Kobra AF.1 C2 models come fitted with an oil container with
a capacity of 1 litre.
INSTALLATION (FIg.2)
Once you have taken the machine out of its packaging,
position the head of the machine (A) on the cabinet (B) and
insert the end of the hose (M) into the connector (N).
Take the container of oil which came with the machine,
unscrew the cap seal and dispose of it, insert the tube of oil
(O) and screw the cap back on properly.
OPERATION:
When you have plugged the machine in, turn the knob (H) to
the position “I”. The light (G) will come on for a few seconds
and the machine will start a shredding cycle.
During the first few minutes of operation, the cutting knives
might NOT be properly oiled since the oil feeder is not yet
completely full. In order to make it fill up more quickly,
trigger the photo cells inside the mouth so that the shredder
runs empty for 8/10 minutes straight.
Now your shredder is ready for operation and the cutting
knives are oiled.
It is recommended to periodically check the level of oil in the
container inside the cabinet.
REPLACINg THE OIL CONTAINER
Open the door.
Take out the empty oil container (P) out of its housing,
unscrew the cap on the top (Q) and extract the oil tube (O).
Get a new oil container, remove the seal cap and dispose of
it, insert the oil tube (O) and screw the cap on tightly.
Put the new oil container back in its housing and close the
door.
Now your shredder is ready for operation.
Attention!
During the first few minutes of operation, the cutting knives
might NOT be properly oiled since the oil feeder is not yet
completely full. In order to make it fill up more quickly,
trigger the photo cells inside the mouth so that the shredder
runs empty for 8/10 minutes straight.
Now your shredder is ready for operation and the cutting
knives are oiled.
Fire hazard
NEVER use synthetic oil, benzene based products or aerosol
lubricants of any kind inside or in the vicinity of the machine
ACCESSORIES
COMBINATION SAFETY LOCK
only for model Kobra AF.1 (Fig.4)
On request
the Kobra AF.1 can be fitted with a combination
safety lock for the top cover of the feeder tray to ensure
safety of documents during shredding.
COVER BLOCK FUNCTION:
Open the top cover of the paper feeder tray as shown in
figure 3.
Insert the documents to be shredded into the paper feeder
tray.
Close the top cover of the paper feeder tray and the machine
automatically starts shredding.
Key in the four-digit PIN number on the keyboard (B), for
example:
and the cover blocks automatically.
The top cover of the shredder unblocks automatically when:
-
the four-digit PIN number is entered.
-
The shred cycle has been completed.
Important
: If you forget the PIN number, the top cover will
unblock automatically 20 minutes after it goes on stand-by.
