Kobold KDF-9 Operating Instructions Manual Download Page 8

 

Operating Instructions KDF-9/KDG-9

 

 

KDF-9/KDG-9 K04/0922 

 

 

                                            Page 8 

6.1  Mounting / start-up 

When starting up the flowmeter, the following points must be observed:

 

-

 

The variable-area flow meter must be installed perpendicularly (direction of flow from the bottom to the 
top).  

-

 

Take special care to install glass-tube devices free from strain.  

-

 

The size of the product line to be connected must be identical to the size of the device connection.  

-

 

All instruments are shipped with the valve installed at the inlet. By turning the glass tube resp. the fitting, 
the valve also can be installed at the outlet. 

-

 

E/F/A/B 

(option diff.pressure regulator): When using gases, the version for a constant inlet pressure 

with "valve at the top" and for a constant counter pressure with "valve at the bottom" should be used. 
If liquids are involved, the position of the valve does not have any impact on the function of the meter. 

-

 

Slowly

 open the shut‐off valve upstream and downstream of the flowmeter.

 

-

 

When

 measuring liquids, vent the pipes carefully.

 

-

 

When

 measuring gases, increase pressure slowly.

 

-

 

Void

 float impact (e.g. caused by solenoid valves), as this is likely to damage the measuring

 

section or float.

 

6.2  Ambient conditions 

6.2.1  Ambient temperature ranges  

-20°C to +100°C (with limit switch -20° +70°C) 

(risk of breakage due to frost)

 

6.2.2  Storage temperature  

-20°C to +100°C 

6.2.3  Climatic category  

Weather-protected and/or unheated locations 

6.2.4  Degree of protection  

IP65 (EN60529) 

6.2.5  Shock resistance/vibration resistance 

The meter should be protected from shocks and vibrations, which could cause damage. 

6.2.6  Electromagnetic compatibility  

Built in limit switch: 
acc. NAMUR recommendation  NE 21 
Product standard: EN 60947-5-2: 2004 

6.3  Fluid conditions 

6.3.1  Fluid temperature ranges  

without limit switch -20°C to + 100°C 
with limit switch -20°C to + 70°C 

(risk of breakage due to frost)

 

6.3.2  Fluid pressure limit  

16 bar (at 20 degrees Celsius) 

Important:  

All pressure values are for non-hazardous liquids and for devices installed free from strain. 
For 

E/F/A/B,

 (option differential pressure regulator)

 

the maximum unilateral pressure resistance of the 

diaphragm is 

7 bar

6.3.3  Inlet and outlet sections 

Inlet and outlet sections are not required for a linear flow profile of the fluid.  

6.3.4  Physical state:  

Liquid or gaseous 

6.3.5  Pressure for gas measurement 

Summary of Contents for KDF-9



















Reviews: