manualshive.com logo in svg

Knick SensoGate WA 131 H, User Manual

Share
Download
Knick SensoGate WA 131 H User Manual Download Page 3

Return of Products 

Please contact our Service Team before returning a defective device. Ship the cleaned device to 

the address you have been given. If the device has been in contact with process fluids, it must 

be decontaminated/disinfected before shipment. In that case, please attach a corresponding 

Declaration of Contamination (see page 45), for the health and safety of our service personnel.

Safety Information

SensoGate® WA 131 H

Process-Related Risks

Knick Elektronische Messgeräte GmbH & Co. KG assumes no liability for damages 

caused by process-related risks known to the operator, which would in fact not 

 permit the use of the WA 131 H sensor lock-gate.

Be sure to observe:

Work on the sensor lock-gate must only be performed by personnel authorized by 

the operating company and specially trained for handling and operating the sensor 

lock-gate.

For safe operation of the WA 131 H sensor lock-gate, the sealing plug or the inlet hose 

(option) must be mounted on the inlet port.

3

Summary of Contents for SensoGate WA 131 H

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands