KNEGT 304G2 Operation Manual Download Page 82

Page: 82 / 103

304G2

SERIES TRACTOR OPERATION MANUAL

(4) Sink speed of the implement is normal,
but it can’t reach the toppest position or
exceed the toppest position

Extension rod is too short or too long

Adjust the length

(5) Implement cannot be put down

①

Main control valve blocked

②

Sink valve blocked

③

Sink speed control valve is screwed too
much

④

Rapid lift lever is flexural

①

Clean it

②

Clean it

③

Loose it

④

Adjust the rapid lift lever
backwards

7.10 Electrical system

Troubles & possible causes

Fixing methods

(1) Accumulator doesn’t have enouph power

①

Pillar plate sulfurized seriously

②

There is something wrong with the
generator or regulator

③

Wire connect unwell

①

Charge again and remove the
sulfuration

②

Check the generator or regulator

③

Check and repair

(2) The temperature of the accumulator is too
high

Current is too large

Check and adjust

(3) The generator does not generate power

Rotor coil broken

Check and repair

(4) The generator does not charge enough or
charge unsteadily

①

Transmission V belt looses, making
generator rate decline

②

oint of the wire looses

③

Carbon is broken

④

Regulator is damaged

①

Adjust

②

Fasten the bolt

③

Check and repair

④

Check and repair

(5) There is a noise in the generator

①

The generator is installed incorrectly

②

Bearing of generator is broken

③

The rotor meet with the stator or
something else

①

Reinstall

②

Replace

③

Repair

(6) The starter motor does not work

①

The wire is broken or wire joint dosen’t
connect correctly

②

The fuse is broken

③

Battery volume is insufficient

①

Weld or replace the wire, clean
the dirt and fasten the bolt

②

Replace

③

Charge the battery

Summary of Contents for 304G2








































































































Search results

Summary of Contents for 304G2

Reviews:

Related manuals for 304G2

Brands by name

Popular brands

KNEGT 304G2, Operation Manual

Search results

Summary of Contents for 304G2

Reviews:

Related manuals for 304G2

Brands by name

Popular brands