background image

BAC-120063CW-ZEC FlexStat 

     4 

Installation and Configuration Guide, Rev. G

Heat Pump Unit (HPU)

Output 

Terminals

Typical 

Terminal 

Codes

HPU Output Connections

BACnet 

Objects

        Analog 9

O. A. Damper (Optional)

AO9

    GND

Ground

(for Analog Output terminals 7–9)

        

Analog 8

Heat or Cool Valve (Optional)

AO8

        

Analog 7

Static Pressure Setpoint (Optional)

AO7

        Relay 6

W2/E

Emergency Heat (Optional)

BO6

    SC 4–6

R

24 VAC (for Relay terminals 4–6)

        Relay 5

W

Auxiliary Heat (Optional)

BO5

        Relay 4

Y2

Compressor 2 (Optional)

BO4

        Relay 3

Y1

Compressor 1

BO3

    SC 1–3

R

24 VAC (for relay terminals 1–3)

        Relay 2

O/B

Reversing Valve 

(see O/B Note in schematic)

BO2

        Relay 1

G

Fan

BO1

NOTE: 

Connections above are for firmware R2.0.0.4 and later. Earlier 

firmware had the optional static pressure setpoint on Analog Output 

9

 instead of Analog Output 

7

, and it did not have the heating/cooling 

coil valve option (Analog Output 8) or outside air damper (economizer) 

option (Analog Output 9).

 APPLICATION
DEGREES SCALE: °F

APP:

OPT: 1 STAGE
ADDITIONAL SETUP
ZONE

HEAT PUMP

1 or 2 Compressors with Auxiliary and Emergency Heat

NOTE:  Although typical terminal code letters are 

shown, check the schematics of your unit 

for wiring details!

 CAUTION

Relays are for Class-2 voltages (24 VAC) only. Do not 
connect line voltage to the relays!
Do not mistakenly connect 24 VAC to an analog 
output ground.

Illustration 4—HPU Application Connections

Input 

Terminals

HPU Input Connections

BACnet 

Objects

       IN9

Static Pressure Feedback (Optional)

AI9

       IN8

(Unused in this application)

AI8

       IN7

(Unused in this application)

AI7

       IN4

(Unused in this application)

AI4

       IN3

(Unused in this application)

AI3

     GND

Ground

       IN2

DAT

*

AI2

*NOTE: 

The DAT sensor is configured for IN2 in the ADVANCED > 

APPLICATION > ADDITIONAL SETUP > SENSORS menu.

XEE-6111-050 or XEE-6112-50 Transformer

NOTE: Wire to “O” terminal if

reversing valve is energized in 
cooling mode; wire to “B” 
terminal if reversing valve is 
energized in heating mode.

STE-140x Duct Sensor, Type III

From 
Previous 
Network 
Device

Optional Network

HPU
Terminals

TERMINALS

To
Next 
Network 
Device

Optional Static Pressure Reading/Setpoint from/to CSP-4702

AO7

IN9

GND

Optional Heating/Cooling Coil Valve

GND

AO8

Optional Outside Air Damper

GND

AO9 

Summary of Contents for FlexStat BAC-120063CW-ZEC













Reviews: