background image

BAC-120063CW-ZEC FlexStat 

     1 

Installation and Configuration Guide, Rev. G

Installation and Configuration Guide

BAC-120063CW-ZEC FlexStat

Zoning Equipment Controller  

Contents ..................................................................1
Mounting ................................................................1
Application Overview .............................................2

Roof Top Unit (RTU) ................................................ 3
Heat Pump Unit (HPU) ........................................... 4

Connections and Wiring ..........................................5

Wiring Considerations .........................................5
Output Connections ............................................5
Input Connections ...............................................6
Power Connection ...............................................6
Network Wiring ..................................................6
Network EOL (End-Of-Line) Termination ............7

Configuration and Operation ..................................7

Configure the Application and Address ...............7
Setpoints .............................................................8
Heat/Cool, Fan, Occupancy, and Override .........9
Schedules ............................................................9
Trends .................................................................9

Sequence of Operation .........................................10

Zone Hysteresis (Changeover) ...........................10
Zone Status .......................................................10

Troubleshooting ....................................................11
Maintenance .........................................................11
Customization .......................................................11
Remote (BAC-5051E) Interface .............................11
IoT (KMC Commander) Interface ..........................12
Additional Resources ............................................12
Important Notices .................................................12

Mounting

Contents

1.  Complete rough-in wiring at each location prior 

to the FlexStat’s installation. Cable insulation 

must meet local building codes.

 CAUTION

To prevent mounting screw heads from touching 
the circuit board in the thermostat, use only the 
mounting screws supplied by KMC Controls. 
Using other screws may damage the FlexStat. 
Do not turn screws in farther than necessary to 
remove the cover.

2.  If the cover is locked on the backplate, turn the 

hex screws in the bottom and top of the FlexStat 

CLOCKWISE

 until they (just) clear the cover. 

(See Illustration 1.) Pull the cover away from the 

backplate (mounting base).

3.  Route the wiring through the backplate.
4. 

With the embossed “UP” and arrows toward the 

ceiling,

 fasten the backplate to a wall electrical 

box. This FlexStat mounts directly on 

vertical

 2 x 

4 inch boxes but requires an HMO-10000W wall 

mounting plate for horizontal or 4 x 4 boxes.

5.  Make connections to the terminal blocks. (See 

Connections and Wiring on page 5

.)

6.  Push the FlexStat cover over the backplate 

while 

being careful not to pinch or dislodge any 

wiring

. Back the hex screws (

counterclockwise

out of the brackets until they engage the FlexStat 

cover and hold it in place.

Illustration 1—Dimensions and Installation

A

B

EIA-485 data 

port (for quick 

network access)

Terminal blocks 

on backplate 

Dimensions in Inches (mm)

A

B

C

1.125 (29)

5.551 (141)

4.192 (106)

Cover locking hex screws

Embossed “UP” indicator

C

NOTICE

OBSERVE PRECAUTIONS 

FOR HANDLING

ELECTROSTATIC

SENSITIVE DEVICES

Summary of Contents for FlexStat BAC-120063CW-ZEC













Reviews: