background image

BAC-9000 Series Controller Installation Guide 

8 921-019-01F

SAMPLE (BAC-9001) WIRING

DAT

10K Ohm

Type 3

Thermistor

Ethernet

To

BLK

SHLD

RED

Controller

Next

To

Controller

Previous

From

BLK

RED

SHLD

(Optional)

STE-1405

NOTE: 

Connect the 

STE-9xxx

 (or

         

STE-6010/6014/6017

 with

         no ventilation control) sensor
         to the Room Sensor port
         using a max. of 150 feet
         of Ethernet patch cable.

CAUTION: 

Do NOT connect 24 VAC to the

              analog outputs (UO3–UO5 and GNDs)!

NOTE:

 For 

MS/TP

 models, turn the

         End Of Line switch ON at both
         physical ends of the MS/TP
         network. Connect the cable
         shield to earth ground at only
         one point.

NOTE:

 For 

Ethernet

 models, connect the

         controller to the network with a
         standard Ethernet patch cord.

NOTE:

 Analog 

inputs

 accept 1K or 10K

         sensors, 0–12 VDC, or 4–20 mA.

NOTE:

 For 

more wiring examples,

 see the

         wiring diagrams that are part of the
         application library in KMC Connect,
         Converge, or TotalControl.

STE-9521

STE-6010-10

(Single Duct VAV, Series Fan Powered with Floating Reheat and Vent Control)

L

H

1/4" (6.35) FR tubing

to flow sensor

~

COM

24 VAC

(Only)

~

Phase

Neutral

Fan

Start

Fan

Speed

+

OPEN CLOSE

COM

Floating

Reheat

UI3

RDY

COM

GND

UI4

PRESSURE SENSOR

HIGH

LOW

-A

+B

S

BACnet MS/TP

EOL

10/100

ETHERNET

BAC-9001/9001CE Controller

~

H

N

Line

Voltage

CONNECTIONS (SAMPLE)

UI3 = DAT SENSOR

INPUTS

OUTPUTS (Binary/Triac)

OUTPUTS (Universal/Analog)

ROOM SENSOR

NETWORK

POWER

MS/TP OR ETHERNET

UO4 = FAN SPEED

BO6 = FAN ENABLE

BO7 = OPEN VALVE

BO8 = CLOSE VALVE

UI5

GND

UI6

UO3

GND

UO4

GND

UO5

ROOM

SENSOR

BO6

BO7

SC

BO8

BO9

OFF

ON

NOTE: 

Use 

24 

V

AC

 (only) on triac outputs

         (BO6–BO9 with SC)!

Summary of Contents for BAC-9001










Reviews: