background image

BAC-9000 Series Controller Installation Guide 

3 921-019-01F

14

NOTE: 

The Ethernet patch cable should be a 

maximum of 150 feet (45 meters).

   CAUTION 

On Conquest “E” models, do NOT 

plug a cable meant for Ethernet 

communications into the Room Sensor 

port! The Room Sensor port powers a 

NetSensor, and the supplied voltage 

may damage an Ethernet switch or 

router.

15

16

NOTE: 

Auxiliary VAV equipment such as fans, 

heaters, reheat valves, and discharge 

air temperature sensors can be 

connected to the controller.

2.  Connect auxiliary VAV equipment to the input 

and output 

green terminal blocks

 

17

.

 CAUTION 

Do 

NOT

 connect 24 VAC to the analog 

outputs (UO3–UO5 and GNDs)!

NOTE: 

Use 24 V

AC

 (only) with triac outputs 

(BO6–BO9 with SC).

NOTE: 

Wire sizes 12–24 AWG can be clamped 

in each terminal.

12

13

7.  Attach the controller to the VAV box with a 

#8 sheet metal screw 

through the 

mounting 

bushing 

12

.

8.  Evenly tighten the 

V-clamp nuts

 

11

 on the 

drive hub to 30–35 in-lb.

CONNECT SENSORS AND EQUIPMENT

NOTE: 

A digital 

STE-9000 Series NetSensor

 

can be used for configuring the 

controller (see 

Configure/Program 

the Controller on page 7

). After the 

controller has been configured, an 

STE-6010

STE-6014

, or 

STE-6017

 

analog sensor can be connected to the 

controller in place of the NetSensor. 

See the relevant installation guide for 

additional details.

NOTE: 

See 

Sample (BAC-9001) Wiring on 

page 8

 for more information.

1.  Plug an 

Ethernet patch cable

 

14

 connected 

to an STE-9xxx or STE-6010/6014/6017 

sensor into the controller’s (

yellow

 

22

ROOM 

SENSOR

 

15

 port.

Summary of Contents for BAC-9001










Reviews: