background image

BAC-9000 Series Controller Installation Guide 

5 921-019-01F

see 

Planning BACnet Networks 

(Application Note AN0404A)

.

NOTE: 

The EOL switch is shipped from the 

factory in the OFF position.

3.  If the controller is at either end of a BACnet 

MS/TP network (only one wire under each 

terminal), turn the 

EOL

 

switch

 

24

 

to 

ON

.

24

CONNECT POWER

NOTE: 

Follow all local regulations and wiring 

codes.

1.  Connect a 24 VAC, Class-2 transformer to 

the 

black power terminal block

 

25

 of the 

controller.

A.  Connect the neutral side of the transformer 

to the controller’s 

common terminal

 

⊥ 

26

.

B.  Connect the AC phase side of the 

transformer to the controller’s 

phase 

terminal

 

∼ 

27

.

26

27

25

NOTE: 

Connect only one controller to each 

transformer with 12–24 AWG copper 

wire.

NOTE: 

Use either shielded connecting cables 

or enclose all cables in conduit to 

maintain RF emissions specifications.

NOTE: 

Also on the newer models, the Room 

Sensor port is 

yellow

 

22

 instead of 

black to help differentiate it from the 

black Ethernet ports.

22

21

NOTE:

  The Ethernet patch cable should be 

T568B Category 5 (or better) and a 

maximum of 328 feet (100 meters) 

between devices.

CONNECT (OPTIONAL) MS/TP NETWORK

1.  For a BAC-9001 or BAC-9021, connect the 

network to the gray 

BACnet MS/TP

 

network 

terminal block

 

23

.

NOTE: 

Use 18 gauge AWG shielded twisted 

pair cable with maximum capacitance 

of 51 picofarads per foot (0.3 meters) 

for all network wiring (Belden cable 

#82760 or equivalent).

23

A.  Connect the 

–A

 terminals in parallel with 

all other 

–A

 terminals on the network.

B.  Connect the 

+B

 terminals in parallel with all 

other 

+B

 terminals on the network.

C.  Connect the 

shields

 of the cable together 

at each device using a wire nut or the 

S

 

terminal in KMC BACnet controllers.

2.  Connect the cable shield to a good earth 

ground at 

one end only

.

NOTE: 

For principles and good practices 

when connecting an MS/TP network, 

Summary of Contents for BAC-9001










Reviews: