Klimaire KSIB009-H2161 Owner'S Manual Download Page 20

1.

2.

Select a position where the condensing water can be easily drained out, and the place

is easily connected for outdoor unit.

4.

Can select the place where is strong enough to withstand the full weight and vibration of
the unit. And will not increase the noise.

5.

6.
7.
8.

Make sure that the indoor unit installation should accord with installation dimension 

diagram requirements. 

3.

Select a location where the children can not reach.

1.

The unit installation work must be done by qualified personnel according to the local

rules and this manual.

2.

Before installating, please contact with local authorized maintenance center, if unit is

not installed by the authorized maintenance center, the malfunction may not solved,

due to discommodious contacts.

3.

W

4.

the appliance must be  positioned so that the plug is accessible

hen removing the unit to the other place, please firstly contact with the authorized

Maintenance Center in the local area.

Notices for installation

Important Notices

Basic Requirements For Installation Position

Install in the following place may cause malfunction. If it is unavoidable contact with 

service center please:

Place where strong heat sources, vapors, flammable gas or volatile object are emitted.

Place where high-frequency waves are generated by radio equipment, welders and 

medical equipment.

Place where a lot of salinities such as coast exists.

Place where the oil (machine oil) is contained in the air.

Place where a sulfured gas such as the hot spring zones is generated.

Other place with special circumstance.

Indoor Unit Installation Position Selection

The air inlet and outlet vent should be far from the obstruction, make sure that the air

can be blown through the whole room.

Be sure to leave enough space to allow access for routine maintenance. The height of the

installed location should be 250cm or more from the floor.

Select a place about 1m or more away from TVset or any other electric appliances.

Select a place where the filter can be easily taken out.

.

Do not use the unit in the immediate surroundings of a laundry a bath a shower or a

swimming pool.

9

17

Summary of Contents for KSIB009-H2161





























Reviews: