www.klever-mobility.com
www.klever-mobility.com
48
49
• Check the inside of the tyre for sharp objects that could
have caused the puncture and remove them. If the fabric
of the tyre is damaged, replace the tyre too. Start the
mounting of the inner tube by inserting the valve into the
valve hole in the rim and infl ate the tube with very little air
pressure until it is wrinkle-free.
• Now mount the inner tube without any creases underneath
the tyre (image 6.24).
• Starting opposite of the valve, lift the tyre bead over the
fl ange of the rim and pull it deep into the rim. Lift the rest
of the tyre by hand over the rim’s shoulder. Do not use tyre
levers, as this may damage the inner tube.
• Push the valve a little back into the tyre, so that the bead of
the tyre is correctly seated in the rim.
• Pull the valve back again and infl ate the inner tube to the
recommended tyre pressure.
6.8 Luggage carrier and transport of
luggage
Your Klever E-bike has a robust and durable aluminium luggage
carrier (image 6.25). The carrier is compatible with the majority
of all standard panniers, and you can use it in conjunction with
an extensive range of accessories. Please note, the maximum
load capacity of the luggage carrier is 25 kg.
Please note! When transporting luggage make sure that
you do not exceed the total maximum permitted weight
of 150 kg., being the combination of speed p
c luggage.
Caution! The additional weight of luggage on your rear
carrier changes the handling of the bike and makes the
required braking distance longer as well.
6.9 Anti-theft protection
This Klever E-bike comes with a motor lock and immobiliser
combined with an acoustic alarm system. The battery can
only be removed from its docking station by unlocking the
battery lock with the key (see section 5.5.3 Removal and
mounting of the battery pack). We recommend to also use a
robust and high-quality chain lock in order to be able to lock
the vehicle to solid fi xtures.
Image 6.25
Image 6.23
Image 6.24
Bicycle parts of your E-bike
Bicycle parts of your E-bike
Tyres
The tyre size can be found on the sidewall. It is printed in
millimetres and inches: 27.5”x 2.35” and 57 – 584 mm. The
wheel has a diameter of 584 mm. (27.5”) and a width of 57
mm. (2.35”).
Please note! The recommended tyre pressure is indicated
on the sidewall of the tyres (2,0 – 4,0 bar; 30 – 55 Psi).
Please note! Regularly check the correct tyre pressure
and pressurise your tyres if necessary. The tyre uses an
inner tube with Schrader valve. So, you can check and
infl ate the tyre at any gas station.
Caution! Above or below, never exceed the recommended
air pressure range. The tyre and the tube can be damaged
and this may lead to sudden loss of air with risk of an
accident. Too low tyre pressure causes higher rolling
resistance. As a consequence, this reduces the range of
your battery.
Disassembly, repair & assembly of the tyres
Regularly check the tyres for cracks and for its thread pattern
height. In case you fi nd that cracks or sharp objects have
damaged the fabric of the tyre or the thread pattern is no
longer suffi
cient, replace the tyres. If in doubt, ask your Klever
dealer who can verify the tyre and replace it.
In the case of a fl at tyre, do as follows:
• Always use plastic tyre levers.
• Remove the wheel as described above.
• Defl ate the tyre and push a tyre lever underneath the tyre
bead opposite of the valve and lift the tyre over the rim fl ange.
• Push the second tyre lever underneath the tyre bead in a
distance of 10 cm. from the fi rst one (image 6.23). If the tyre
is still very tight around the rim, then use a third tyre lever
as well.
• Now, you can lift the tyre over the whole circumference of
the rim with the help of one of the levers. The inner tube
can be removed.
• In case the leak cannot be found easily, hold the infl ated inner
tube into a bucket of water and look for the rising air bubbles.
• Repair the tube according to the instructions on the repair
kit. Or if necessary, replace it. In case of replacement, make
sure you buy the correct size inner tube.
